Advanced Technology Video CS7D37PB Manuel utilisateur
Please read this manual thoroughly before use, and keep it handy for future reference.
Design and specifications are subject to change without notice.
Mini Strip Camera
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
CAUTION : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
WARNING : This is a Class A poduct. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
FCC INFORMATION : This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
2
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.. Do not block any ventilat ion openings. Install in accord ance with the manufacturer`s
instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the ca rt, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
9. CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2
power source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
IMPORTANT SAFETY INSTRUCTIONS
3
4
INTRODUCTION
IMPORTANT : The user of this camera is responsible for checking and
complying with local, state, and federal laws and statutes concerning the
recording and monitoring of audio signals.
Features:
High resolution and high performance 1/3" Color CCD
Excellent picture quality
700 lines of resolution(Color)
0.1 lux(Color), 0.04ux(B/W) @ F1.2 50IRE Sensitivity
Auto electronic shutter [1/60(1/50) ~ 1/100,000]
Auto white balance
AGC (Auto Gain Control)
Use Certified / Listed Class 2 power source only
2D DNR
(Digital Noise Reduction)
Side Light Compensation
3.7mm Pin hole Lens
BNC (Video connection) 2-Pin terminal block (Power)
Operates in DC12~15V +/- 10%
5
The gimbal mount surface mounted to ceiling.
Default position out of the box is for vertical orientation of the camera view.
For horizontal orientation of camera the housing must be opened by removing the 4,M3 button
head screws located on each side of the housing.
Camera module rotates 90 degrees in the desired direction.
* The gimbal mount surface mounted vertically.
* The gimbal mount surface mounted horizontally.
Module support
Camera module
Module support
Camera module
Open the box and unwrap the camera housing. Remove the top and bottom M6 Allen head screws
and seperate the gimbal mount from the housing.
Drill a feet-thru hole for the camera cable on the mounting surface.
Step 1
6
Feed wire through the 3/4" hole on the gimble mount.
For vertical mounting penetrate door frame at 63 inches from the finished floor.
The gimbal can be mounted on the top door jam if required.
Mount the gimbal horizontally
Mount the gimbal vertically
Step 2
Step 3
Mount the gimbal horizontally
Mount the gimbal vertically
Center the gimbal mount to mounting surface and mark the mounting holes for the gimbal
mount on the surface.
Secure the gimbal mount to the surface using installer supplied self tappers for aluminum
frame structure.
If mounting on soft surface such as drywall be sure to use to use anchors.
For drop ceiling tiles it is recommended that toggle bolts be used as anchors.
7
Pull cable from headend thru the mount gimbal mount. Connect BNC connectors and mark
power connection to the camera.
Note: Polarities must be observed the camera is 12V DC and damage will result if power
polarities are not observed. Power connector has a positive center pin.
Mount the housing to the gimbal using the M6 Allen head screws at the top and bottom.
Place the external tooth washer between the housing and the gimbal mount then the split
lock washer on the M6 screw and insert the screw into the housing through the gimbal
mount and external tooth lock wasker. Install the bolt and washers assembly at the bottom
and top of the gimbal mount finger tight.
Adjust the camera housing right or left to acquire the proper field of view for the installation.
Completing the housing installation
* Camera lens position can be adjusted up and down 5 degrees
Split lock washer between gimbal mount and housing
External tooth lock washer under head of bolt
M6 Allen head screw
Interface Cable for power and video connection to head end cable.
o
92 o
5
o
92 o
5
o
92
Step 4
8
DIMENSIONS
MINI STRIP CAMERA inch
9
SPECIFICATIONS
Power source
Power consumption
Image sensor
Number of pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
Min. illumination
Video output
Power input
AGC
Lens mount
2:1 interlace
15.734KHz(H) x 59.94Hz(V)
Internal
1/60 ~ 1/100,000 sec.
700 TV lines (Color)
0.1 lux(COLOR), 0.04 lux(BW) @ F1.2, 50 IRE
More than 50dB (AGC off)
976(H) x 582(V)
Terminal Block
Fixed mount
NTSC
130mA (1.5 Watts)
976(H) x 494(V)
MODEL
S/N ratio
White Balance
Power
15.625KHz(H) x 50Hz(V)
1/50 ~ 1/100,000 sec.
Lens
Connector
&
etc.
PAL
Video output
Operating Temperature
1.0 Vp-p (75 ohm, composite)
Auto(ATW)
BNC Connector
o]
-10 C ~ +50 C [14 F ~ 122 F
o o o
General
ON
Operating humidity 0 ~ 96% (non-condensing)
1/3" Color CCD
Day / Night Auto
* Use the power consumption 2W over.
Side Light Compensation
Digital Noise Reduction
Auto
2D DNR
DC12~15V +/-10%
External Dimension
Weight
1.8"(W) x 6.4"(H) x 1.4"(D)
set : 325g packing : 535g
F3.7mm Pin hole Fixed
10
Table des matières
Autres manuels Advanced Technology Video Caméra de sécurité
Advanced Technology Video
Advanced Technology Video IPB3TWI Manuel utilisateur
Advanced Technology Video
Advanced Technology Video VDP690WDR Manuel utilisateur
Advanced Technology Video
Advanced Technology Video HDCB225 Manuel utilisateur
Advanced Technology Video
Advanced Technology Video CLP5050I Manuel utilisateur
Advanced Technology Video
Advanced Technology Video IPSD302TWI Manuel utilisateur
Advanced Technology Video
Advanced Technology Video FD650WDR Manuel utilisateur
Advanced Technology Video
Advanced Technology Video I PSD302TWI Manuel utilisateur
Advanced Technology Video
Advanced Technology Video hdg-t3x2 series Manuel utilisateur
Advanced Technology Video
Advanced Technology Video PERFORMANCE VD600TDNW Manuel utilisateur
Advanced Technology Video
Advanced Technology Video SVD410SN Manuel utilisateur
