ADTRAN NT1 ACE4 Manuel utilisateur
NT1 ACE4
User Manual
1200242L1: NT1 ACE4
336012VUR01: Power Supply 12 VDC/800 mA
61200242L1-1A
September 2000
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
(256) 963-8000
© 2000 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
61200242L1-1 NT1 ACE4User Manual iii
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety pre-
cautions should always be followed to reduce the risk of
fire, electric shock and injury to persons. The precautions
are listed below.
1. Donotusethisproductnearwater(forexam-
ple,nearabathtub,washbowl,kitchensinkor
laundry tub, in a wet basement or near a swim-
ming pool).
2. Never install telephone jacks in wet locations un-
lessthejackisspecificallydesignedforwetloca-
tions.
3. Avoid using a telephone (other than a cordless
type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
4. Donotusethetelephonetoreportagasleakinthe
vicinity of the leak.
5. Use only the power cord, power supply, and/or
batteries indicated in the manual. Do not dispose
of batteries in a fire. They may explode. Check lo-
cal codes for any special disposal instructions.
6. Never touch uninsulated telephone wires or ter-
minals unless the telephone line has been discon-
nected at the network interface.
7. Use caution when installing or modifying tele-
phone lines.
SAVE THESE INSTRUCTIONS.
iv NT1 ACE4User Manual 61200242L1-1
AFFIDAVIT REQUIREMENTS FOR CONNECTION TO
DIGITAL SERVICES
• An affidavit is required to be given to the telephone
company whenever digital terminal equipment with-
out encoded analog content and billing protection is
used to transmit digital signals containing encoded
analog content which are intended for eventual con-
version into voiceband analog signals and transmitted
on the network.
• The affidavit shall affirm that either no encoded ana-
log content or billing information is being transmitted
or that the output of the device meets Part 68 encoded
analog content or billing protection specifications.
• End user/customer will be responsible to file an affi-
davit with the local exchange carrier when connecting
unprotected CPE to a 1.544 Mbps or subrate digital
services.
• Until such time as subrate digital terminal equipment
is registered for voice applications, the affidavit re-
quirement for subrate services is waived.
61200242L1-1 NT1 ACE4User Manual v
AFFIDAVIT FOR CONNECTION OF CUSTOMER
PREMISES EQUIPMENT TO 1.544 MBPS AND/OR
SUBRATE DIGITAL SERVICES
For the work to be performed in the certified territory of
_______________
(telco name)
State of ___________________
County of _________________
I, ______________________________(name),
________________________________(business address),
______________________ (telephone number) being duly
sworn, state:
Ihaveresponsibilityfortheoperationandmaintenanceof
the terminal equipment to be connected to 1.544 Mbps
and/or ________ subrate digital services. The terminal
equipment to be connected complies with Part 68 of the
FCC rules except for the encoded analog content and bill-
ing protection specifications. With respect to encoded an-
alog content and billing protection:
( ) I attest that all operations associated with the estab-
lishment,maintenance,andadjustmentof thedigitalCPE
with respect to analog content and encoded billing pro-
tection information continuously complies with Part 68 of
the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing
encodedanalogcontentorbillinginformationwhichisintended
to be decoded within the telecommunications network.
vi NT1 ACE4User Manual 61200242L1-1
( ) The encoded analog content and billing protection is
factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital
CPE responsible for the establishment, maintenance, and
adjustment of the encoded analog content and billing in-
formation has (have) been trained to perform these func-
tionsbysuccessfullyhavingcompletedoneofthe
following (check appropriate blocks):
( ) A. A training course provided by the manufacturer/
grantee of the equipment used to encode analog signals;
or
( ) B. A training course provided by the customer or au-
thorized representative, using training materials and in-
structions provided by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) C. An independent training course (e.g., trade school
or technical institution) recognized by the manufacturer/
grantee of the equipment used to encode analog signals;
or
( ) D. In lieu of the preceding training requirements, the
operator(s)/maintainer(s) is (are) under the control of a
supervisor trained in accordance with _________ (circle
one) above.
I agree to provide _________________ (telco's name) with
proper documentation to demonstrate compliance with
the information as provided in the preceding paragraph,
if so requested.
61200242L1-1 NT1 ACE4User Manual vii
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of ________, 199___
_________________________________
Notary Public
My commission expires:
_________________________________
viii NT1 ACE4User Manual 61200242L1-1
FCC INFORMATION
This device complies with Part 15 of the FCC rules. Oper-
ation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications to this unit not ex-
pressly approved by the party responsible for
compliance could void the user's authority to op-
erate the equipment.
Canadian Standards Association
This device must be powered by a CSA approved power
supply or a power supply meeting the requirements of
CS03, Part I Section 1.4.2.
FCC regulations require that the following
informationbeprovidedinthismanual:
1. This equipment complies with Part 68 of the FCC
rules. On the bottom of the equipment housing is a la-
bel that shows the FCC registration number for this
equipment. If requested, provide this information to
the telephone company.
61200242L1-1 NT1 ACE4User Manual ix
2. If this equipment causes harm to the telephone network,
the telephone company may temporarily discontinue
service. If possible, advance notification is given; oth-
erwise, notification is given as soon as possible. The
telephone companywilladvisethecustomeroftheright
to file a complaint with the FCC.
3. The telephone company may make changes in its facili-
ties, equipment, operations, or procedures that could af-
fect the proper operation of this equipment; advance
notification and the opportunity to maintain uninter-
rupted service is given.
4. If experiencing difficulty with this equipment, please con-
tact ADTRAN for repair and warranty information. The
telephone company may requirethisequipment to be dis-
connected from the network until the problem is correct-
ed, or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modular plug
is provided with this equipment. In addition, an FCC
compliant cable appropriate for the dial backup option
orderedisprovidedwiththisequipment. Thisequip-
ment is designed to be connected to the telephone net-
work or premises wiring using an FCC compatible
modular jack, which is Part 68 compliant.
xNT1ACE
4User Manual 61200242L1-1
7. The following information may be required when ap-
plying to the local telephone company for leased line
facilities.
8. The FCC recommends that the AC outlet, to which
equipment requiring AC power is to be installed, is pro-
videdwithanACsurgearrester.
Service
Type Digital Facility
Interface Code Service
Order Code Network
Jacks
ISDN 02IS5 6.0N RJ-49C
Table des matières
Autres manuels ADTRAN Alimentation
ADTRAN
ADTRAN 61175044L2-22B Manuel utilisateur
ADTRAN
ADTRAN D4PBCU0 Guide de maintenance et de service
ADTRAN
ADTRAN NetVanta 1760-12F Manuel utilisateur
ADTRAN
ADTRAN NetVanta 1000 Series Mode d’emploi
ADTRAN
ADTRAN 3192 Manuel utilisateur
ADTRAN
ADTRAN NetVanta 1110 Manuel utilisateur
ADTRAN
ADTRAN TOTAL ACCESS 4303 PLUS Manuel utilisateur
ADTRAN
ADTRAN Total Access 850 Mode d’emploi
ADTRAN
ADTRAN NetVanta 1131 RPS/EPS Manuel utilisateur
ADTRAN
ADTRAN Power Supply/Battery Charger Manuel utilisateur
ADTRAN
ADTRAN 4303 DC Manuel
ADTRAN
ADTRAN NT1 T400 Manuel utilisateur
ADTRAN
ADTRAN Total Access 1500 Mode d’emploi
ADTRAN
ADTRAN TOTAL ACCESS MX2800 Manuel utilisateur
ADTRAN
ADTRAN Total Access 850 Mode d’emploi
ADTRAN
ADTRAN NetVanta 1131 RPS/EPS Manuel utilisateur
ADTRAN
ADTRAN ATLAS 890 Manuel utilisateur
ADTRAN
ADTRAN HDSL 851 Mode d’emploi
