Adjustables MRT2T8-PM Manuel utilisateur

OPERATION GUIDE

www.adjustablesbyleggett.com

99300828-b EDR10783 12/06

CONTENTS

MR2T8-PM Function ............................................................................................ 4

J Box Programming Procedure .......................................................................... 5

Power Down Box Operation ..............................................................................5

MR2T8-PM Programming (1 hand control - 1 bed) .......................................... 6

MR2T8-PM Programming (2 hand controls - 1 bed).............................................7

MR2T8-PM Programming (1 hand control - 2 beds)..........................................8

MR2T8-PM Programming (2 hand controls - 2 beds) ...................................... 9

MR2T8-PM Reprogramming (separating 2 beds) .......................................... 10

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM FUNCTION

IMPORTANT INFORMATION

READ ADVISORY INFORMATION IN THE OWNERS MANUAL CAREFULLY BEFORE USING THIS

PRODUCT. THE POTENTIAL FOR ELECTRICAL SHOCK EXISTS IF ELECTRICAL COMPONENTS

ARE NOT INSTALLED OR OPERATED PROPERLY.

HAND CONTROL REQUIRES FOUR (4) AAA SIZE BATTERIES. TO CONSERVE

BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY

BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.

NOTE

POSITION RECALL BUTTONS

Press to recall a position or

massage function set by the

program set button.

TRANSMISSION

INDICATOR LIGHT

Verifies a button is being pressed

and data is being sent to the bed.

FOOT UP/DOWN BUTTONS

Press and hold to raise or lower

the foot section.

FOOT MASSAGE BUTTONS

Press and hold the increase

button to activate the foot

massage at high intensity. Press

the decrease button to reduce

foot massage intensity. To turn off

foot massage, press and hold the

decrease button until the

massage turns off.

FLAT BUTTON

Press and release to return the

bed to the flat position. This

button will also turn off the

massagers.

HEAD MASSAGE BUTTONS

Press and hold the increase

button to activate the head

massage at high intensity. Press

the decrease button to reduce

head massage intensity. To turn

off head massage, press and hold

the decrease button until the

massage turns off.

HEAD UP/DOWN BUTTONS

Press and hold to raise or lower

the head section.

PROGRAM SET BUTTON

Use to program any position of

the bed as a favorite position (3

unique positions). Press the

position recall buttons (1, 2 or 3)

to return bed to any of the

programmed positions.

To Program Favorite Positions:

1. Set the head and/or foot to the

desired position.

2. Press the program set button once

and release.

3. Wait 2 seconds, press position

recall button 1 to save position.

4. Repeat steps 1 thru 3 above to

program favorite positions for

recall buttons 2 and 3.

MR2T8-PM Hand Control Operation Guide 99300828-b

J BOX PROGRAMMING PROCEDURE

When programming the hand control,

unplug the adjustable bed electrical

power cord. Wait 30 seconds, then plug

the cord back in to the power source.

This simple process automatically sets

the bed to the program mode for 90

seconds. For convenience, use this

procedure in lieu of pressing the learn

button (located on the J Box, mounted to

the underside of the bed base frame).

J BOX PROGRAMMING

For adjustable beds equipped with “J box” only—no power down box.

At any point where “press the learn

button” is designated, disconnecting and

reconnecting the electrical power cord

will achieve the same function. Note that

this alternate programming feature is

only applicable to beds without a power

down box. Power down equipped

adjustable beds require use of the learn

button when programming the hand

control.

POWER DOWN BOX OPERATION

In case of a power outage, press and

hold the learn button on the power down

box to lower the bed to the flat position

(FIGURE 1).

This function is only for lowering the bed

and will not operate the bed to any other

position. The (2) 9 volt batteries should

be replaced after this function is used.

In the event the power down feature

does not work, check to make sure the

(2) 9 volt batteries are good.

LEARN

BUTTON

FIGURE 1: Power down box learn button.

POWER

DOWN BOX

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM PROGRAMMING 1 hand control - 1 bed

The two step procedure below is required to program 1 hand control to operate 1 bed.

Before beginning, make certain the bed is plugged into a working grounded electrical

outlet. If programming fails, initiate the programming procedure a second time.

STEP 1

The bed will be equipped with either a

power down box or J box receiver unit

(FIGURE 2). Locate the receiver unit for

the bed and press the learn button for 1

second and release. Note: If you

experience difficulty locating or reaching

the learn button on a J box equipped

adjustable bed, refer to J Box

Programming on page 5.

STEP 2

On the hand control, simultaneously

press and hold the preset 1 and foot up

buttons (FIGURE 3). The transmission

indicator light will flash slowly and then

flash rapidly to indicate programming

mode. Continue to hold for 5 seconds

and then release the buttons.

One hand control is now programmed to

operate one bed.

FIGURE 2: Power down box and J box receiver units.

POWER

DOWN BOX

POWER DOWN

BOX IS NOT

MOUNTED TO

BED FRAME.

J BOX IS

MOUNTED TO

THE BOTTOM

SIDE OF THE

BED FRAME.

LEARN

BUTTON

LEARN

BUTTON

J BOX

FOOT UP

BUTTON

TRANSMISSION

INDICATOR

LIGHT

FIGURE 3

PRESET 1

BUTTON

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM PROGRAMMING 2 hand controls - 1 bed

The three step procedure below is required to program 2 hand controls to operate 1

bed. Before beginning, make certain the bed is plugged into a working grounded

electrical outlet. If programming fails, initiate the programming procedure a second

time.

STEP 3

Repeat Step 1 and Step 2 with hand

control 2.

Two hand controls are now programmed

to operate one bed.

STEP 1

The bed will be equipped with either a

power down box or J box receiver unit

(FIGURE 2). Locate the receiver unit for

the bed and press the learn button for 1

second and release. Note: If you

experience difficulty locating or reaching

the learn button on a J box equipped

adjustable bed, refer to J Box

Programming on page 5.

STEP 2

On hand control 1, simultaneously press

and hold the preset 1 and foot up

buttons (FIGURE 3). The transmission

indicator light will flash slowly and then

flash rapidly to indicate programming

mode. Continue to hold for 5 seconds

and then release the buttons.

HAND

CONTROL 1

HAND

CONTROL 2

FIGURE 2: Power down box and J box receiver units.

POWER

DOWN BOX

POWER DOWN

BOX IS NOT

MOUNTED TO

BED FRAME.

J BOX IS

MOUNTED TO

THE BOTTOM

SIDE OF THE

BED FRAME.

LEARN

BUTTON

LEARN

BUTTON

J BOX

FOOT UP

BUTTON

TRANSMISSION

INDICATOR

LIGHT

FIGURE 3

PRESET 1

BUTTON

OPERATE ONLY ONE (1) HAND CONTROL AT

A TIME. OPERATING TWO (2) HAND

CONTROLS AT THE SAME TIME WILL

MOMENTARILY BLOCK BOTH RF SIGNALS

AND PREVENT BOTH CONTROLS FROM

FUNCTIONING.

NOTE

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM PROGRAMMING 1 hand control - 2 beds

The three step procedure below is required to program 1 hand control to operate 2

beds. Before beginning, make certain the beds are plugged into a working grounded

electrical outlet. If programming fails, initiate the programming procedure a second

time.

BED 2

BED 1

STEP 3

Repeat Step 1 and Step 2 for bed 2.

One hand control is now programmed to

operate two beds.

STEP 1

The bed will be equipped with either a

power down box or J box receiver unit

(FIGURE 2). Locate the receiver unit for

the bed and press the learn button for 1

second and release. Note: If you

experience difficulty locating or reaching

the learn button on a J box equipped

adjustable bed, refer to J Box

Programming on page 5.

STEP 2

On the hand control simultaneously

press and hold the preset 1 and foot up

buttons (FIGURE 3). The transmission

indicator light will flash slowly and then

flash rapidly to indicate programming

mode. Continue to hold for 5 seconds

and then release the buttons.

FIGURE 2: Power down box and J box receiver units.

POWER

DOWN BOX

POWER DOWN

BOX IS NOT

MOUNTED TO

BED FRAME.

J BOX IS

MOUNTED TO

THE BOTTOM

SIDE OF THE

BED FRAME.

LEARN

BUTTON

LEARN

BUTTON

J BOX

FOOT UP

BUTTON

TRANSMISSION

INDICATOR

LIGHT

FIGURE 3

PRESET 1

BUTTON

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM PROGRAMMING 2 hand controls - 2 beds

The six step procedure below is required to program 2 hand controls to operate 2 beds. Before

beginning, make certain the beds are plugged into a working grounded electrical outlet. If

programming fails, initiate the programming procedure a second time.

STEP 5

On hand control 1, simultaneously press and

hold the preset 1 and the foot up buttons

(FIGURE 3). The transmission indicator light

will flash slowly and then flash rapidly to

indicate programming mode. Continue to hold

for 5 seconds and then release the buttons.

STEP 6

Repeat Step 4 and Step 5 with hand control 2.

Two hand controls are now programmed to

operate two beds.

STEP 1

The bed will be equipped with either a power

down box or J box receiver unit (FIGURE 2).

Locate the receiver unit for the bed and press

the learn button for 1 second and release.

Note: If you experience difficulty locating or

reaching the learn button on a J box equipped

adjustable bed, refer to J Box Programming on

page 5.

STEP 2

On hand control 1, simultaneously press and

hold the preset 1 and the foot up buttons

(FIGURE 3). The transmission indicator light

will flash slowly and then flash rapidly to

indicate programming mode. Continue to hold

for 5 seconds and then release the buttons.

STEP 3

Repeat Step 1 and Step 2 with hand control 2.

STEP 4

The bed will be equipped with either a power

down box or J box (FIGURE 2). On bed 2, press

the learn button for 1 second and release.

FIGURE 2: Power down box and J box receiver units.

POWER

DOWN BOX

POWER DOWN

BOX IS NOT

MOUNTED TO

BED FRAME.

J BOX IS

MOUNTED TO

THE BOTTOM

SIDE OF THE

BED FRAME.

LEARN

BUTTON

LEARN

BUTTON

J BOX

HAND

CONTROL 1

BED 1

HAND

CONTROL 2

BED 2

OPERATE ONLY ONE (1) HAND CONTROL AT

A TIME. OPERATING TWO (2) HAND

CONTROLS AT THE SAME TIME WILL

MOMENTARILY BLOCK BOTH RF SIGNALS

AND PREVENT BOTH CONTROLS FROM

FUNCTIONING.

NOTE

FOOT UP

BUTTON

TRANSMISSION

INDICATOR

LIGHT

FIGURE 3

PRESET 1

BUTTON

MR2T8-PM Hand Control Operation Guide 99300828-b

MR2T8-PM REPROGRAMMING separating 2 beds

The six step procedure below is required to separate 2 hand controls from operating 2 beds. One

hand control per bed operation will result. Before beginning, make certain the beds are plugged into

a working grounded electrical outlet. If programming fails, initiate the programming procedure a

second time. NOTE: OPERATE ONLY ONE (1) HAND CONTROL AT A TIME. OPERATING TWO (2) HAND

CONTROLS AT THE SAME TIME WILL MOMENTARILY BLOCK BOTH RF SIGNALS AND PREVENT BOTH

CONTROLS FROM FUNCTIONING.

STEP 4

The bed will be equipped with either a power

down box or J box (FIGURE 2). On bed 2, press

the learn button for 1 second and release.

STEP 5

On hand control 2, simultaneously press and

hold the preset 1 and the foot up buttons

(FIGURE 3). The transmission indicator light

will flash slowly and then flash rapidly to

indicate programming mode. Continue to hold

for 5 seconds and then release the buttons.

STEP 6

Repeat Step 4 and Step 5 with hand control 2.

Independent hand control operation is now

restored (hand control 1 operating bed 1; hand

control 2 operating bed 2).

STEP 1

The bed will be equipped with either a power

down box or J box receiver unit (FIGURE 2).

Locate the receiver unit for the bed and press

the learn button for 1 second and release.

Note: If you experience difficulty locating or

reaching the learn button on a J box equipped

adjustable bed, refer to J Box Programming on

page 5.

STEP 2

On hand control 1 simultaneously press and

hold the preset 1 and foot up buttons (FIGURE

3). The transmission indicator light will flash

slowly and then flash rapidly to indicate

programming mode. Continue to hold for 5

seconds and then release the buttons.

STEP 3

Repeat Step 1 and Step 2 with hand control 1.

Note: wait 90 seconds before proceeding to

Step 4.

HAND

CONTROL 1

BED 1

HAND

CONTROL 2

BED 2

FIGURE 2: Power down box and J box receiver units.

POWER

DOWN BOX

POWER DOWN

BOX IS NOT

MOUNTED TO

BED FRAME.

J BOX IS

MOUNTED TO

THE BOTTOM

SIDE OF THE

BED FRAME.

LEARN

BUTTON

LEARN

BUTTON

J BOX

FOOT UP

BUTTON

TRANSMISSION

INDICATOR

LIGHT

FIGURE 3

PRESET 1

BUTTON

Table des matières

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur