ADF NMV Series Manuel utilisateur

Owner’s Manual

NMV / NMR

Inbuilt Appliances

Supplied by:

Castworks Pty Ltd

57 Industrial Drive

Braeside VIC 3195

TESTED IN ACCORDANCE WITH AS/NZS 4013:2014 and AS/NZS 2918.

Please read this manual thoroughly before installing and starting your free-standing appliance.

Keep these instructions for future reference

V12072018

Index

1. Introduction 03

2. Appliance Layout 05

3. Technical Specifications 06

4. Installation Instructions 09

Chimney build out Version 10

Cabinetry / Full Wall Build Install / Zero Clearance 15

Ducting 20

Flue Outlet 23

5. Fan 26

6. Instructions for use 28

7. Cleaning and Maintenance 30

8. Troubleshooting 32

9. Warranty 33

CE Marking label with serial number

1. Introduction

Congratulations on your purchase of your new ADF woodfire appliance!

Years of extensive research and dedication to innovation and quality, since 1976, has resulted in these

beautifully designed European appliances, constructed to strict Portuguese and European legislation, and

tested and Certified to the Australian Emissions, Efficiency and Safety standard requirements

guaranteeing excellent performance.

Please read this manual fully to ensure safe and efficient use of your heater and to comply with the

warranty guidelines.

Solid Fuel – Ecological Energy

Through photosynthesis, plants capture energy from the sun and transform it into chemical energy. The

trapped energy, eg in the form of wood, pellets, coal are called biomass fuels and can be converted into

various forms: electricity, fuel or heat. Biomass burning causes the release of carbon dioxide into the

atmosphere, but since this compound had previously been absorbed by the plants that originated the

fuel, the CO2 emissions balance is zero, not contributing to the greenhouse effect on the planet.

Firewood is the most environmentally friendly way of producing heat in your home, as it is a fully

renewable resource. The amount of CO2 that is released during the combustion of firewood is not higher

than the amount that would be released from its natural decomposition. Wood ash is a mineral fertilizer

easily absorbed by the environment in a totally ecological way.

Firewood – Use

Choosing your wood

All wood types have a different calorific value. You should choose only well-seasoned hard woods.Do

not use logs that are too large.Split round logs so they cannot roll and cause a hazard.

Drying your wood

Whichever firewood is chosen, it must be very dry and seasoned. Unseasoned or green firewood does

not heat as much, because a large part of the energy is consumed in the evaporation of the water and

creosote contained in the wood, which is highly corrosive and will damage the appliance and

consequently it could void your Warranty. In addition, moist firewood produces a large amount of

smoke and little flame, which will foul the appliance, the glass and the chimney. When raining the

stored wood should be covered and well ventilated. Generally, green wood should be left to “season”

for two years.

Wood to Avoid

Softwoods and low-density wood: This kind of firewood release a lot of heat but burn too quickly and

projects embers and resin that foul the chimney and the interior of your woodstove.These should be

used as Kindling only, for starting your fire.

Do not use:

Wood with varnish, exotic wood, treated/painted timber, agglomerates that can produce toxic fumes

which will damage the appliance. Do not use drift wood or coastal wood with high salt content, it will

quickly damage the heater.

All ADF appliances are designed to burn firewood and firewood only, with less than 20% moisture

contect. The use of unseasoned firewood or firewood with moisture or other types of fuel not

recommended will void the warranty.See below, the drier the wood the better heat you get out of it.

0.0

1.0

2.0

3.0

4.0

5.0

6.0

010 20 30 40 50 60 70 80 90

(kWh/kg)

Moisture (%)

Moisture Vs Energy released by firewood

2-Appliance Layout

Pos. Designation

1 Door lever, Tool supplied for Door and Air Control

Combustion Air control (Use tool):

Open (+) slide to the right

Close (-) slide to the left

3 Vermiculite brick lining

4 Primary convection outlet

5 Secondary convection outlet (hot air distribution for ducting) Inbuilt only

6 Smoke Outlet – Flue collar 200mm (8” Crimped)

7 Convection inlet

Important:

oPlease read this manual thoroughly before installing and starting your free-standing appliance.

oInstallation must be carried out by a licenced and certified installer.

oKeep these instructions for future reference

3- Technical Specification

Specifications

TESTED IN ACCORDANCE WITH

AS/NZS 4012:2014 & AS/NZS 4013:2014

Burning Harwood

Unit 820 1000

Maximum Avearge Heat Output kW 9.7 12.5

Overall Average Efficiency % 63 64

Particulate Emission Factor g/kg 0.8 1.2

Maximum firewood load kg 9.7 13.7

Minimum clearance distances from combustible materials mm

See page

10/15.

See Page

10/15.

Flue Diameter mm 200 200

Recommended Fuel

Burn only Harwood

Moisture ≤ 20%

Electrical Specification

220-240

50/60

Fan Settings

Thermostat Low, Manual High.

Model

Dimensions (mm)

Width Depth Height Weight

ADF820NM-RS Freestanding

with Bench

832 445 860 198

ADF820NM-RS Freestanding

with Bench and Fan

832 445 860 200

ADF820NMV-B Freestanding

with Fan

832 450 565 160

ADF1000NMV-B Freestanding

1012

450

465

172

ADF1000NMV-B Freestanding

with Fan

1012 450 565 174

ADF1000NMV-P

Pedestal Freestanding

1012 450 865 206

WARNINGS:

A wood burning heater is, by its nature, an appliance that operates at high temperatures, so it is

necessary to take into account potential risk factors that should be avoided at all costs. Children must

be kept away from any combustion appliance and supervised in the room at all times.

Installation must be carried out by a licenced and certified installer.

The installation must meet the requirements of the manufacturers instructions, AS2918 and the Building

Code of Australia.

The appliance must be installed in such a way as to allow easy maintenance.

Incorrect installation may cause serious damage to the equipment and the safety of people and property.

Before installing your appliance, please ensure the following:

oThe appliance must be installed on a heat resistant surface to 600°C.

oThe floor must be structurally sound, to support the installation weight.

oReplacement outside air must be supplied to the room with the heater, a minimum equivalent to

half the cross-sectional area of the flue, ie 160cm2 free air.

oYour appliance must be non-permanently installed and easily accessible to ensure general

maintenance (chimney and equipment).

oThe appliance must not be cemented in its enclosure under any circumstances.3 – 5mm clearance

is required between the heater outer skin and construction materials, to allow for metal expansion.

Keep these instructions for future reference

WARNINGS:

oREFER TO COMPLIANCE LABEL – DISREGARD ANY CONTRADICTORY FUEL TYPE INFORMATION IN

INSTRUCTION MANUAL

oWARNING: THE APPLIANCE & FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/NZS

2918:2001 AND THE APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES.

oWARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH THIS STANDARD SHALL COMPLY WITH

THE REQUIREMENTS OF AS/NZS 4013:2014 WHERE REQUIRED BY THE REGULATORY AUTHORITY,

I.E. THE APPLIANCE SHALL BE IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING “TESTED

TO AS/NZS 4013:2014”.

oANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE

TESTING AUTHORITY IS CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED FOR

COMPLIANCE WITH AS/NZS 4013:2014.

WARNINGS:

oCAUTION: MIXING OF APPLIANCE OR FLUE SYSTEM COMPONENTS FROM DIFFERENT SOURCES OR

MODIFYING THE DIMENSIONAL SPECIFICATION OF COMPONENETS MAY RESULT IN HAZARDOUS

CONDITIONS. WHERE SUCH ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE

CONSULTED IN THE FIRST INSTANCE.

oCAUTION: CRACKED AND BROKEN COMPONENTS, e.g. GLASS PANELS OR CERAMIC TILES, MAY

RENDER THE INSTALLATION UNSAFE.

oWARNING: ANY MODIFICATION OF THE APPLICANCE THAT HAS NOT BEEN APPROVED IN WRITING

BY THE TESTING AUTHORITY IS CONSIDERED AS BREACHING AS/NZS 4013.

oWARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE THE FIRE.

oWARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE VICINITY OF THIS APPLIANCE

WHEN IT IS OPERATING.

oWARNING: DO NOT STORE FUEL WITHIN THE HEATER INSTALLATION CLEARANCES.

oWARNING: WHEN OPERATING THIS APPLIANCE AS AN OPEN FIRE USE A FIRE SCREEN.

oWARNING: OPEN AIR CONTROL (AND DAMPER WHEN FITTED) BEFORE OPENING FIRING DOOR.

oCAUTION: THIS APPLIANCE SHOULD NOT BE OPERATED WITH A CRACKED GLASS.

oTHIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES IN ACCORDANCE WITH

THESE INSTRUCTIONS.

oTHE USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD AS A FUEL CAN BE HAZARDOUS.

oTHE APPLIANCE OR FLUE SYSTEM SHOULD NOT BE MODIFIED IN ANY WAY WITHOUT THE WRITTEN

APPROVAL OF THE MANUFACTURER.

oBURN ONLY HARDWOOD

oPrior to installation check with your state and local authorities regarding any specific regulations that

may apply.

All local regulations, including those referring to national standards, must be observed

when installing the appliance.

4-Installation Instructions

The floor must be structurally sound.

The Hearth must have a heat resistant surface to 600°C, with an insulating thickness of

non-combustible material equivalent to 24mm of cement sheet with thermal conductivity

of 0.1m2.K/W per 9mm. eg 24mm Bellis Board or equivalent.

Dimensions required in front of the heater are shown in the Elevation drawings below.

The hearth must be included beneath the heater (eg 40mm Skamotec).

Heater with Fan option.

If the heater is supplied with legs to protect the Fan during transit; lay the heater on its back, to remove

the legs. The heater can then be carefully put into position. The Heater will need to be inserted into the

chimney build out before the construction is completed.

The Installations can be included into a Masonry installation, built as a default non-combustible chimney

opening meeting the requirements for the National Construction Code or the Building Code of Australia.

The tested installation is built into Skamotec 225. This can be done in 2 ways:

1. Chimney Build Out version (no combustibles within 50mm of each side wall, or

2. Cabinetry version; if Combustible materials will be built alongside the installation. This version

includes as extra side cavity with 50mm clearance each side. See below.

Note:

An Optional Kit form is available for the Chimney Build Out version.

1.Chimney Build Out Install:

The build out is constructed with Skamotec 225 40mm sheets to Skamotec specifications, the

Installation and Clearance specifications are included in the Elevation drawings shown below:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ADF Poêle à bois

ADF

ADF 100 DUO Manuel utilisateur

Manuels Poêle à bois populaires d'autres marques

Plamen

Plamen ECO MINIMAL 50 Manuel utilisateur

Austro Flamm

Austro Flamm KOKO Manuel utilisateur

RAIS

RAIS 800 Manuel utilisateur

Henley

Henley Arklow Manuel utilisateur

Jøtul

Jøtul F 500 Manuel utilisateur

Englander

Englander BLUE RIDGE 100 Manuel utilisateur

WoodPro

WoodPro WS-TS-1500 Manuel utilisateur

Contura

Contura C 586W Manuel utilisateur

Nordpeis

Nordpeis N-20 T Manuel utilisateur

Palazzetti

Palazzetti EVA Guide de configuration

Lopi

Lopi 1250 Republic Manuel utilisateur

Panadero

Panadero CAPRI 3V Manuel de programmation

RAIS

RAIS RONDO 92 Manuel utilisateur

RAIS

RAIS attika NEXO 100 GAS Manuel utilisateur

ADURO

ADURO 15-3 Guide de l'utilisateur

Pacific energy

Pacific energy SUPER 27 SPECTRUM Manuel utilisateur

Avalon

Avalon Olympic 11190 Manuel utilisateur

Ventis

Ventis HES350 Manuel utilisateur