Addvalue Communications BluePendant BP100 Manuel utilisateur
FCC INFORMATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experience radio/TV technician for help for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
No special accessory is required to enable the equipment to comply with the
emission limits.
• Incoming Call
• Outgoing Call
• Call Waiting
• Voice Control
• Volume Control
Contents
Getting Started
Using Your BluePendant
Charging
Troubleshooting
Unpacking Contents
• Power On/Off
• Pairing Process
• Pairing to a Mobile Phone
• Deleting Pairing Information
• Modes
• Low Battery
2
3
7
12
14
1
Additional Information17
77A55017030
Your package should have:
• BluePendant BP100 (Fig 1)
• Power Adaptor (Fig 2)
• Rechargeable Battery (Fig 3)
CALL Button
Indicator Light
Power / Volume Button
(PWR / VOL )
Power Jack
Unpacking Contents
2Unpacking Contents
Fig 1 : Picture of Connecting
Earpiece & Mic from
the BluePendant
Fig 2 : Power Adaptor
Fig 3 : Rechargeable Battery
Getting Started
3
Getting Started
Before the BluePendant can be used for the first time, the
BluePendant battery must be charged with the supplied power
adapter according to steps found in page 12 for Charging.
Power ON / OFF
• To Power ON, press and hold PWR/VOL button until a BEEP
is heard in the BluePendant earpiece. The indicator light turns
Blue for 3 seconds. Thereafter, the indicator light will either flash
Blue, once every 2 seconds (when paired) or alternating Blue
and Orange (when not paired).
• To Power OFF, press and hold the PWR/VOL button until the
indicator light turns OFF. A series of beeps will be heard in the
BluePendant earpiece and the PWR/VOL button is to be released.
• The BluePendant cannot be turned OFF during Charging and
when there is a call in process.
Pairing Process
Before the BluePendant can be used, it must be paired with a
Bluetooth-enabled mobile phone. There is no need to pair the
BluePendant again unless the pairing information has been
deleted from the mobile phone.
Pairing to a Mobile Phone
• Delete pairing information in the BluePendant first. Refer to
page 5 for deleting pairing information.
• The BluePendant is ready for pairing when the indicator light
alternates Blue and Orange. Refer to Phone Operations Guide
to prepare the mobile phone for pairing to the BluePendant.
• During the pairing process, depending on the model, the mobile
phone will request for the PASSKEY, or PAIRING CODE, or
PASSCODE. The code or the PIN is labeled at the back of the
BluePendant battery door.
• Key-in the provided PIN into the mobile phone. The BluePendant
indicator light will continue to alternate Blue and Orange until
the BluePendant is paired to the mobile phone.
4Getting Started
Model: BP100
PIN:12345
Bluetooth
Headset
BluePendant
PASSKEY or
PIN CODE
5
Getting Started
Deleting Pairing Information
• Once pairing information is deleted, the BluePendant resets
to its default settings.
• To delete pairing information, press and hold both PWR/VOL
and CALL buttons until the indicator light alternates Blue and
Orange.
• The BluePendant is ready for pairing.
• Once pairing is completed,
the indicator light will flash
Blue once every 2 seconds.
• The BluePendant is now in
Standby mode and is ready
to accept or initiate calls.
6
Getting Started
Modes
• Pairing mode
- Indicator light alternating Blue and Orange
- BluePendant is ready for pairing to Bluetooth-enabled phone
• Standby mode
- Indicator light flashes Blue once every 2 seconds
- BluePendant ready to accept/initiate calls
• Call mode
- Indicator light shows a steady Blue
- BluePendant has either accepted or initiated a call
• Charging mode
- Indicator light steady Orange
- The BluePendant battery is being charged
• Low Battery mode
- Indicator light flashes Orange
- 3 long beeps can be heard in earpiece
- Battery needs recharging and if BluePendant continues to
operate in this mode, the power will be automatically switched
OFF ultimately
Using Your BluePendant
7
Using Your BluePendant
Once the BluePendant is paired to the mobile phone, it can now
accept or initiate calls as long as it is within range of approximately
up to 10m (30ft) outdoor, or up to 5m (15ft) indoor.
Incoming call
Depending on the mobile phone, calls can be received through
the BluePendant or through the mobile phone. Switching calls
from the BluePendant to the mobile phone and vice versa is
possible. Please refer to the mobile phone user documentation
and the BluePendant Phone Operations Guide for more
information.
• When there is an incoming call, the indicator light shows a
steady Blue.
• When the incoming call ring is heard in the BluePendant
earpiece, press the BluePendant CALL button to answer the
call.
• To end the call, press the BluePendant CALL button and the
indicator light flashes Blue once every 2 seconds.
8Using Your BluePendant
• If the BluePendant loses connection during a call, press and
hold the BluePendant CALL button for 2 seconds to re-establish
connection. A series of BEEPS can be heard in the BluePendant
earpiece when it attempts to re-connect to the mobile phone.
Outgoing call
Depending on the mobile phone, calls can be received through
the BluePendant or through the mobile phone. Switching calls
from the BluePendant to the mobile phone and vice versa is
possible. Please refer to the mobile phone user documentation
and the BluePendant Phone Operations Guide for more
information.
• When making an Outgoing call, dial the number and press the
mobile phone call button.
• The call will be connected to the BluePendant and the indicator
light turns to steady Blue.
• To end the call, press the BluePendant CALL button and the
indicator light flashes Blue once every 2 seconds.
9
Using Your BluePendant
• If the BluePendant loses connection during a call, press and
hold the BluePendant CALL button for 2 seconds to re-establish
connection. A series of BEEPS can be heard in the BluePendant
earpiece when it attempts to re-connect to the mobile phone.
Call Waiting
The Call waiting function is available if the mobile phone supports
it and if call waiting services has been subscribed. Please refer
to the mobile phone user documentation and BluePendant
Phone Operations Guide for more information.
• An incoming call can be answered while a call is in progress,
provided the call waiting service is available.
• Press the CALL button to answer the second call.
Voice Control
The Voice Control function can be used only if the mobile phone
supports it. Please refer to the mobile phone user documentation
and the BluePendant Phone Operations Guide for more
information.
Table des matières
