Add-A-Motor 80 Manuel utilisateur

ADD-A-MOTOR PART INSTALLATION Side 1 of 2

Motor housing has 9 screws (refer to Screw Index).

It is very important that correct screws are installed back in locations shown.

DO NOT over-tighten these screws because that can damage the housing.

STEP 1: Remove Screws #1 and #2. Then, lift-off Rear-Cover to access interior.

STEP 3: Leave wires attached to motor terminals. STEP 4: Remove Screws #4.

Separate housings. Guide the Circuit Board out.

ADD-A-MOTOR PART INSTALLATION Side 1 of 2

Motor housing has 9 screws (refer to Screw Index).

It is very important that correct screws are installed back in locations shown.

DO NOT over-tighten these screws because that can damage the housing.

STEP 1: Remove Screws #1 and #2. Then, lift-off Rear-Cover to access interior.

STEP 3: Leave wires attached to motor terminals. STEP 4: Remove Screws #4.

Separate housings. Guide the Circuit Board out.

Screws #1

Screws #2

Screws #3

Remove

Screws #4

SCREW INDEX

Screw 1: 2-1/4” long (2 each)

Screw 2: 3/4” long (2 each)

Screw 3: 1/2” long (3 each)

Screw 4: 1” long (2 each)

Remove Rear-Cover

DO NOT remove

this screw unless

installing a new

Gearmotor.

Open housing as shown.

Front Cover

Assembly

Screws #1

Screws #2

Screws #3

Remove

Screws #4

SCREW INDEX

Screw 1: 2-1/4” long (2 each)

Screw 2: 3/4” long (2 each)

Screw 3: 1/2” long (3 each)

Screw 4: 1” long (2 each)

Remove Rear-Cover

DO NOT remove

this screw unless

installing a new

Gearmotor.

Open housing as shown.

Front Cover

Assembly

STEP 2:

- Leave Red & Black wires attached to motor terminals.

- Carefully bend both motor terminals up to vertical.

- Grasp Circuit Board, lift up and unsnap it from its 2 mounting posts.

- Remove both Screws #3.

STEP 2:

- Leave Red & Black wires attached to motor terminals.

- Carefully bend both motor terminals up to vertical.

- Grasp Circuit Board, lift up and unsnap it from its 2 mounting posts.

- Remove both Screws #3.

Remove

Screws #4

Remove

Screws #4

REMOVE BROKEN DRIVE SHAFT INSTALL NEW DRIVE SHAFT Side 2 of 2

1. Example of broken Drive Shaft stub protruding from Gearmotor. Install new Drive Shaft by pushing only in direction shown.

2. Turnover. Push gear-end of Drive Shaft only in direction shown. Push thru Gearmotor hub until gear-end protrudes fully.

CAUTION: Force needed. Protect hands, housing and motor.

REPLACE FRONT COVER ASSEMBLY

VERY IMPORTANT – MODEL 80 DRAPERY MOTOR ONLY – TO PREVENT DAMAGE:

1. BEFORE installing motor, OPEN drapery HALFWAY.

2. IF EVER drapery does not close properly, make BOTH adjustments below soon as possible:

A. ADJUST motor to STOP as soon as drapery is fully closed, and also …

B. ADJUST motor to STOP 4 inches or more BEFORE FULL OPEN.

3. ALWAYS, ALWAYS, ALWAYS keep motor adjusted to STOP 4 inches or more BEFORE FULL OPEN.

REMOVE BROKEN DRIVE SHAFT INSTALL NEW DRIVE SHAFT Side 2 of 2

1. Example of broken Drive Shaft stub protruding from Gearmotor. Install new Drive Shaft by pushing only in direction shown.

2. Turnover. Push gear-end of Drive Shaft only in direction shown. Push thru Gearmotor hub until gear-end protrudes fully.

CAUTION: Force needed. Protect hands, housing and motor.

REPLACE FRONT COVER ASSEMBLY

VERY IMPORTANT – MODEL 80 DRAPERY MOTOR ONLY – TO PREVENT DAMAGE:

1. BEFORE installing motor, OPEN drapery HALFWAY.

2. IF EVER drapery does not close properly, make BOTH adjustments below soon as possible:

A. ADJUST motor to STOP as soon as drapery is fully closed, and also ...

B. ADJUST motor to STOP 4 inches or more BEFORE FULL OPEN.

3. ALWAYS, ALWAYS, ALWAYS keep motor adjusted to STOP 4 inches or more BEFORE FULL OPEN.

Model D20

Lift-Reel

Model 80

Axle

Front Cover Assembly interior showing 2-sided

black Control Gear mounted on white post

(small gear must face down).

Also shown is Stop Switch and 3 terminals.

Connect Green wire to left terminal, White to

center, and Yellow to right terminal.

G W Y

DO NOT remove the 6

screws in Gearmotor

unless replacing a gear.

2. Push gear-end ONLY

in direction shown and

then discard it.

After

install,

gear

should

protrude

fully

thru hub.

Model D20

Lift-Reel

DO NOT remove the 6

screws in Gearmotor

unless replacing a gear.

2. Push gear-end ONLY

in direction shown and

then discard it.

After

install,

gear

should

protrude

fully

thru hub.

Model 80

Axle

Front Cover Assembly interior showing 2-sided

black Control Gear mounted on white post

(small gear must face down).

Also shown is Stop Switch and 3 terminals.

Connect Green wire to left terminal, White to

center, and Yellow to right terminal.

G W Y

1. Stub-end of

broken drive shaft.

1. Stub-end of

broken drive shaft.

Ce manuel convient aux modèles suivants

Autres manuels Add-A-Motor Moteur

Add-A-Motor

Add-A-Motor 80 Manuel utilisateur

Manuels Moteur populaires d'autres marques

Rotax

Rotax 125 senior MAX evo Manuel utilisateur

Kohler

Kohler K361 Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

Kohler

Kohler COMMAND CH18-745 Manuel utilisateur

Mercury

Mercury D4.2L D-Tronic Manuel utilisateur

Selve

Selve SE Plus-RC Series Manuel utilisateur

Perkins

Perkins 1206E-E66TA Manuel utilisateur

Skov

Skov DA 174 Manuel

Rossi

Rossi TX11 Series Manuel utilisateur

Siemens

Siemens SIMOTICS T-1FW3 Feuille d'instructions

AL-KO

AL-KO PRO 350 Manuel utilisateur

MTU

MTU 12 V 4000 Lx4 Manuel utilisateur

Nanni

Nanni N3.30 Manuel d'instructions

Nanni

Nanni N5.160 CR2 Manuel utilisateur

KSB

KSB SuPreme Series Instructions d'installation

Hiwin

Hiwin EM1 Series Manuel utilisateur

Rotax

Rotax 912 i series Mode d'emploi

Siemens

Siemens SIMOTICS XP 1MB1 Manuel utilisateur