ActionTec 11 Mbps Wireless Access Point Manuel utilisateur

11 Mbps

Wireless Access Point

User’s Manual

Table of Contents

I. Introduction 2

II. Contacting Technical Support 3

III. Introduction to Wireless Networks 4

IV. Installing the Actiontec 11 Mbps Wireless Access Point 7

V. Configuring the Actiontec 11 Mbps Wireless Access Point 11

VI Troubleshooting 21

VII Frequently Asked Questions 22

VIII Regulatory Notes and Statements 24

IX Warranty Statements 26

Proprietary Notice and Disclaimer

Unless otherwise noted, this document and the information herein disclosed are proprietary

to Actiontec Electronics, Inc the manufacturer. Any person or entity to whom this document

is furnished or who otherwise has possession thereof, by acceptance agrees that it will not be

copied or reproduced in whole or in part, nor used in any manner except to meet the purposes

for which it was delivered.

The information in this document is subject to change without notice and should not be con-

strued as a commitment by Actiontec the manufacturer. Although Actiontec the manufacturer

will make every effort to inform users of substantive errors, Actiontec the manufacturer dis-

claims all liability for any loss or damage resulting from the use of this document or any hard-

ware or software described herein, including without limitation contingent, special or inci-

dental liability.

Note: PC is a trademark of IBM Corporation. Windows 98 and 98 SE is a trademark of

Microsoft Inc. All other brand or product names and logos used in this manual are trademarks

or registered trademarks of their respective holders.

Table of Contents

0530-0320-000

Page

2Introduction

Thank you for purchasing the Actiontec 11 Mbps Wireless Access Point. This Wireless

Access Point is easy to use and easy to setup. If you like the freedom of accessing your net-

work from anywhere within your home or office, then take your networking to the next

level with the Actiontec 11 Mbps Wireless Access Point. You will be able to have full access

to your network and share files, printers and even your High-Speed Internet access.

Package Contents

Make sure the following items came in this package:

Actiontec 11 Mbps Wireless Access Point and power adapter

Actiontec 11 Mbps Wireless Access Point Installation CD-ROM

This User’s Manual and Quick Start Installation Guide

Warranty Card

Minimum System Requirements

PC Computer with an Ethernet Adapter configured for TCP/IP.

Internet Browser (Microsoft Explorer, Netscape Navigator, etc..).

Microsoft Windows 2000/Windows Millennium Edition, Windows 98, Second

Edition (SE), XP/Windows NT 4.0

Introduction

Contacting Technical Support

Actiontec Electronics prides itself on making high-quality, durable, high-performance

products. If you should need assistance, the Actiontec Technical Support Department is

available seven days a week from 6 am to 11pm (Mountain Time), to provide profes-

sional support.

Contacting Technical Support

Actiontec Electronics, Inc.

760 N. Mary Avenue

Sunnyvale, CA 94085

Phone: 1-719-884-8300 E-mail: [email protected]

lll

4Introduction to Wireless Networks

A wireless network connects computers to each other using radio technology that

allows you the freedom to move around the area and to work anywhere within reach

of an Access Point.

The Actiontec 11 Mbps Wireless Access Point can be connected to a wired network,

allowing communication between the wired network and computers using Actiontec

11 Mbps Wireless PC Cards. This technology is an extension to the existing Ethernet

networking standard, so you can connect the Actiontec Wireless Access Point to an

existing Ethernet network.

Adding Access Points to Your Network

Placement and connection of the Actiontec Wireless Access Point depends entirely on

your specific (network) environment. The Actiontec Wireless Access Point can be

used for the following configurations:

Creating a wireless network.

Extending an existing wired Ethernet network.

Connecting to a single computer.

Creating a Wireless Network

Your Actiontec Wireless Access Point can be used to setup a wireless network as

shown in Figure 1. Follow the steps below to create a wireless network.

Introduction to Wireless Networks

Figure 1: Creating a Wireless Network

lll

Introduction to Wireless Networks

Note: Refer to the appropriate user manual for successful installation of your

wireless network.

1. Prepare one computer that you will want to connect wirelessly.

(Install wireless network card and software).

2. Configure the IP settings for this client computer.

3. Install the Actiontec Wireless Access Point.

4. Your 802.11b wireless network is now ready.

5.For further functionality and security, the Actiontec Wireless Access Point

can be configured using the Actiontec Wireless Access Point Configuration util-

ity and the Web Interface.

6. Install other client computers if this is applicable to your environment

Extending a Wired Network with One or More WirelessAccess Points

When the Actiontec Wireless Access Point is used as an extension to a wired network

(figure 2), please make sure that the current wired network is completely

functional.

Follow these steps to extend you wired network:

1. Install the Actiontec Wireless Access Point and connect it to your wired network

via an open Ethernet port in your switch or hub.

2. You can now use the wireless network.

Figure 2: Extending a Wired Network

lll

6Introduction to Wireless Networks

3. For further functionality and security, the Actiontec Wireless Access Point can

be configured using the Actiontec Wireless Access Point Configuration

utility and the Web Interface

4. Install the wireless client computer(s).

Connecting an Access Point Directly to a Computer

Your Actiontec Wireless Access Point can be connected directly to your computer

as shown in figure 3.

Note: Refer to the appropriate user manual for successful installation of your wireless

network.

Follow these steps to connect your Actiontec Wireless Access Point directly to your

computer:

1. Install a network interface card (NIC) in the computer you want to connect the

Actiontec Wireless Access Point to.

2. Configure the IP settings for this client.

3. Install the Access Point.

Note: For this connection you need to use a cross-over Ethernet cable.

4. You can now use the wireless network.

5. For further functionality and security, the Actiontec Wireless Access Point can

be configured using the Actiontec Wireless Access Point Configuration

utility and the Web Interface.

6. Install the wireless client computer(s).

Figure 3: Connecting Directly to a Computer

Installing the Actiontec Wireless Access Point

This equipment is designed with the utmost care for the safety of those who install

and use it. However, special attention must be paid to the dangers of electric shock

and static electricity when working with electronic equipment. All guidelines in

this manual and of the computer manufacturer must therefore be followed at all

times to ensure the safe use of the equipment.

Physical Installation of the Actiontec 11 Mbps Wireless Access Point

For the best performance and range, the Actiontec Wireless Access Point needs to

be placed in an upright vertical position as shown in Figure 4.

Installing the Wireless Access Point

Important Notice

This device is a 2.4 GHz low power RF device intended for home and office use in

all EU member states except in France where restrictive use applies. For further

information, refer to “Regulatory notes and statements”

Figure 4: Actiontec 11 Mbps Wireless Access Point

8Installing the Actiontec Wireless Access Point

The Actiontec Wireless Access Point can be installed in 2 different ways:

On a desktop.

Determine a clear area on your desktop where the Actiontec Wireless Access

Point can be placed in an upright position clear of obstructions.

Mounted on a wall.

Prior to drilling holes into a wall, make sure the wall area of interest is clear of

electrical wiring or water pipes.

Determine the position of the screws and mark with a pencil.

Drill holes in the wall at the location of the marks.

Insert plastic lugs into the holes

Fasten the screws into the plastic lugs, making sure to leave a 3mm distance

as clearance between the wall and screw heads.

Mount the Actiontec Wireless Access Point onto the screws.

Figure 5: Actiontec Wireless Access Point on a desktop

Figure 6: Actiontec Wireless Access Point on a wall

Installing the Actiontec Wireless Access Point

Connecting the Access Point to a Network

Now that your Actiontec Wireless Access Point has been installed, it is ready to be

connected to the power outlet and to your wired network.

1. Attach the power adapter output connector to the Actiontec Wireless Access

Point, plug it into an AC outlet and check the power LED to confirm if you are

connected properly.

2. Identify the Ethernet port, which is located next to the power connector on the

Actiontec Wireless Access Point.

3. Attach the Ethernet cable to the Actiontec Wireless Access Point and connect the

cable on the other end to either a hub in the network or a computer. Please see

the note below for proper connection.

Figure 7: Actiontec Wireless Access Point connectors

If the Actiontec Wireless Access Point is connected to an Ethernet switch or

hub, a “normal” (not a cross-wired) Ethernet cable must be used.

If the Actiontec Wireless Access Point is connected directly to a computer, a

“cross-wired” (not a normal) Ethernet cable must be used.

Connecting to a switched Ethernet port is recommended so that the full 11

Mbps bandwidth of the Access Point is dedicated.

Autres manuels pour 11 Mbps Wireless Access Point

Table des matières

Autres manuels ActionTec Point d'accès sans fil

ActionTec

ActionTec V2000H Manuel utilisateur

ActionTec

ActionTec 11 Mbps Wireless Access Point Manuel utilisateur

ActionTec

ActionTec 802AA Manuel utilisateur

ActionTec

ActionTec USB Driver R3010UW(AP) Manuel utilisateur

ActionTec

ActionTec AU802C Manuel utilisateur

ActionTec

ActionTec 802.11b Wireless Access Point Manuel utilisateur

ActionTec

ActionTec GT701AP Manuel utilisateur

ActionTec

ActionTec MyWirelessTV 2 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur