ACTi PMAX-0318 Manuel utilisateur
Outdoor Mini Dome
Mounting on a Straight Wall
using PMAX-0318 Wall Mount
Installation Guide
For Models:
A88, A92, A94, A96 Ver. 2020/12/15
www.acti.com
Hardware Manual
2
Table of Contents
Precautions 3
Safety Instructions ...........................................................................5
Wall Mount Installation Procedures 6
Step 1: Prepare for Installation........................................................7
Step 2: Mount the Camera ...............................................................8
Step 3: Manage the Cables ..............................................................9
Step 4: Install the Wall Mount........................................................10
Step 5: Connect to Network........................................................... 11
Step 6: Adjust the Viewing Angle.................................................. 11
Step 7: Close the Dome Cover....................................................... 12
Other Installation 13
How to Move the Camera Cable From Side to Bottom................13
Accessing the Camera 16
Configure the IP Addresses...........................................................16
Using DHCP Server to Assign IP Addresses................................16
Using the Default Camera IPAddress..........................................18
Access the Camera......................................................................... 20
www.acti.com
Hardware Manual
3
Precautions
Read these instructions
Read all the safety and operating instructions before using this product.
Heed all warnings
Adhere to all the warnings on the product and in the instruction manual. Failure to follow the
safety instructions given may directly endanger people, cause damage to the system or to other
equipment.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
ACTi andACTi logo are registered trademarks of ACTi Corporation. All other names and products
used in this manual are registered trademarks of their respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. ACTi will not be held responsible for any
typographical or technical errors and reserves the right to make changes to the product and
manuals without prior notice.
www.acti.com
Hardware Manual
4
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the users will be required to correct the interference at
their own expense.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.
www.acti.com
Hardware Manual
5
Safety Instructions
Cleaning
Disconnect this product from the power supply before cleaning.
Accessories and Repair Parts
Use only the accessories and repair parts recommended by the manufacturer. Using other
attachments not recommended by the manufacturer may cause hazards.
Installation
Install other devices (such as PoE injector, alarm, etc.) that will be used with the camera in a dry
place protected from weather,
Servicing
Do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the product.
3) If the inner parts of product have been directly exposed to rain or water.
4) If the product does not operate normally even by following the operating instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the product to its normal operation.
Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine if the product is in proper operating condition.
www.acti.com
Hardware Manual
6
Wall Mount Installation Procedures
Perform the following procedures to install the camera on a straight wall using the Wall Mount if
the cable will pass through a hole on the wall.
Before starting the installation, make sure that the wall where the camera will be installed can
support more than the total weight of the camera with the mounting accessories and other cables.
Prepare the following materials needed for installation:
Wall Mount package:
oWall mount
oScrews for camera
oDrill Template
Screwdriver
Screws (x2) to attach the Wall Mount to the wall (not supplied, purchase screws
applicable to the wall material where the Wall Mount will be installed)
Ethernet cable
Waterproof Tape
NOTE: The camera images shown in the succeeding pages are provided for reference only,
actual camera may slightly differ.
www.acti.com
Hardware Manual
7
Step 1: Prepare for Installation
1. Attach the bundled drill template (included in the Wall Mount package) on the wall and drill
the screw holes and the cable hole on the wall.
2. Loosen the four (4) screws using the hexagon wrench bundled with the camera.
3. Lift to remove the dome cover.
4. If necessary, insert a memory card into the memory card slot of the camera with the metallic
contacts of the card facing down the camera.
www.acti.com
Hardware Manual
8
Step 2: Mount the Camera
1. Check whether the camera comes with the cable coming out from the side or the bottom
cable hole.
If the cable is coming out from the bottom hole of the camera, insert the cable through
the wall mount.
If the cable is coming out from the side cable hole, you can do one of the following:
A. Remove the bottom tab of the wall mount. Then, leave the cable as it is and proceed
to the next step (installing the camera on the wall mount). The cable can later go
through the gap on the wall mount.
B. Remove the cable coming out from the camera side and move it to go through the
bottom cable hole, see How to Move the Camera Cable From Side to Bottom on
page 13 for instructions. This method provides a cleaner installation but the
procedure is a bit tedious. Depending on the installation environment, you may skip
this step and do Option A instead.
www.acti.com
Hardware Manual
9
2. Using the four (4) screws bundled with the Wall Mount, install the camera to the wall mount
with the screw holes marked as “2”.
Step 3: Manage the Cables
1. Route the cables from the network side through the hole on the wall and connect the Ethernet
cable to the Ethernet port of the camera. If using a power adapter, you may also connect it to
the camera power connector, at this point.
2. Check if the connection is working. If ok, then wrap the cable connections with waterproof
tape to protect the cables from water or other environmental factors. Note that, waterproofing
must be done from the yellow label towards the connectors.
DISCLAIMER: Make sure to apply proper waterproofing method to the cable connectors.
ACTi will not be responsible for camera damage caused by improper waterproofing
application, improper installation or the misuse of equipment for installation.
c
Ethernet
DC12V Power
www.acti.com
Hardware Manual
10
3. If the camera cables are coming from the side cable hole of the camera, remove the bottom
tab on the wall mount, then route the cable through the gap.
4. Push the cables through the wall or inside the wall mount.
Step 4: Install the Wall Mount
Attach the wall mount to the wall with two (2) screws.
Table des matières
Autres manuels ACTi Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur