Acson AAD13A Manuel utilisateur
1
OPERATION MANUAL
AROMA DIFFUSER
AAD13A
2
CONTENTS
1.0
Introduction
4
2.0
Product Overview
5
3.0
How to Use
6
4.0
Safety Instructions
9
5.0
Maintenance
13
6.0
Troubleshooting
14
DISCLAIMER
In complying with the policy for continuous improvement of Acson
Malaysia Sales & Service Sdn Bhd (herein after referred to as “Acson”),
the information contained in this document is subjected to change
without prior notice. While Acson makes no commitment to update or
provide current information automatically to the manual owner, that
information (if applicable) can be obtained by contacting the nearest
Acson office, distributors or dealers network. It is the responsibility of
the operator or service personnel to verify the applicability of these
documents, then prior to working on the equipment. They should verify
with the owner whether the equipment has been modified and if current
literature is available.
3
CAUTION
Please do not pour water directly on the mist outlet or it will damage
the product.
4
INTRODUCTION
Aroma diffuser or essential oil diffuser adopts the principle of ultrasonic
atomization. During the processof dispersing the essential oil, theroom
is filled with the fragrance. It could act as a humidifier to retain the
moisture in the air if no essential oil is added.
Product
Aroma Diffuser
Model Name
AAD13A
Volume
130 ml
Rated Voltage
5V
Rated Power
5W
Unit Dimension
(HxWxD)
160 x 106 x
106 mm
Net Weight
0.24 kg
Material
ABS+PP
5
PRODUCT OVERVIEW
Mist Outlet
Cover
Mist Outlet
USB Port
Splashboard
Air Outlet
Water Level
Sensor
On/ Off
Button
Air Inlet/ Water
Drain Hole
6
HOW TO USE
1. Open the cover.
2. Add moderate amount of water and essential oil.
The water level should not beyond the maximum water level
indication.
Add few drops of essential oil into water.
Volume of
Water Added
Suggested Amount
of Essential Oil
Duration
50 ml
1-2 drops
30 min –1 hour
100 ml
2-4 drops
1 –2 hours
130 ml
4-6 drops
2 –3 hours
7
Note: Please do not remove the water level indicator when adding the
water to prevent water level from exceeding maximum level indication.
3. Connect to power supply.
Connect the USB cable to any USB power source.
When the power supply is connected, Standby Mode is activated.
The unit will flash yellow light for once.
Maximum Water Level
Water Level Sensor
8
4. Activate the mist function.
Press the mist button for once, it will activate Continuous Mode.
Unit will keep misting until user turn off the unit.
Press it again, the unit will then switch to Interval Mode. Unit will
mist for 10 seconds, pause for 10 seconds, then mist again.
Press it again, the unit will return to Standby Mode.
5. Activate the ambient light.
Press the light button, warm light is turned on.
Press it again, Rainbow Mode is activated by switching between
7 colours ambient lighting.
Press it again, the colour of light is fixed at the selected colour.
Press it again to turn off light function.
Mist button
Light button
9
SAFETY INSTRUCTIONS
1. The unit must be powered with correct power supply.
2. It is prohibited to fill water directly into the mist outlet.
3. The misting effect is slightly different between each units after they
are manufactured. Various factors are identified to be effecting the
misting effect, such as types of water, surrounding temperature,
humidity and direction of wind.
4. If the water is lower than certain predefined level, the unit will flash
red light for 5 times to indicate water shortage. In case of water
shortage, misting function could not be used, where light function
could be used as usual.
5. Corrosive liquids are prohibited to be in touch with the unit, or else
it will damage the unit.
6. In the event of replacement of essential oils, please follow the safety
instructions and cleaning tips to clean the unit.
Note: When the water is running out, the misting will be stopped. Unit will
flash red light for 5 times to indicate water shortage. Then it will
automatically switch to Standby Mode.
10
SAFETY INSTRUCTIONS
In case of unit tilting or water pouring out, please proceed with the
following safety instructions:
1. Shut down the unit and pull the power cord out of unit.
2. Pour out the remaining water. Do not pour out from the air outlet (as
shown in the following picture) to prevent water entering the circuit
board.
3. Lean the unit and drain the remaining water from the air inlet.
4. Leave the unit in a cool dry place for 24 hours to let it dry completely.
Air Inlet/ Water
Drain Hole
On/ Off Switch
Table des matières
Langues :
