Acroprint CARD READ SENSOR Manuel d'utilisation et d'entretien

CARD READ SENSOR CALIBRATION INSTRUCTIONS

FOR

MODEL ATT 310

The sensor in the Model ATT 310 will need to be re-calibrated when the following criteria are met.

If unit:

1) Misreads cards

2) Rejects cards

3) The card read sensor board is changed

4) The control board is damaged or is disconnected from the driver board

To re-calibrate the sensors if a unit is misreading or rejecting cards and the control board is not to

be removed from the unit, please follow the instructions below:

1) With the unit plugged in, remove the top case of the clock.

2) Push the reset switch (SW6) on the control board. The print head will cycle and the unit emits a beep

and the display will read 12:00.

3) Turn on all 8 DIP switches on DIPSW2.

4) While holding down switch SW1, push the reset switch (SW6) once.

5) As soon as the LCD display comes on, release SW1. At this point, the display will show 12:00, but

the print head will not cycle and there will be no beep.

6) Use the ATT 310 time card number S103.

7) Insert the TOP EDGE of the card into the ATT 310 so the large black strips are facing down and the

left edge of the card is flush with the left side of the clock base. The ATT 310 will beep twice if it

reads the stripe correctly. If it does not read it correctly, it will beep once. (This step has calibrated

the unit for the back strip.)

SW6

SW1

8) Next, turn off all the 8 switches on DIP SW2 and turn on all 8 switches on DIP SW1. Insert the

time card with the black stripes facing down and the right edge of the card flush with the right

side of the clock base. If it reads correctly, it will beep twice. If not, it will beep once. (This step

calibrates the ATT 310 for the blank area of the card)

9) Once the unit has accepted the blank area of the card, PRESS THE RESET SWITCH ONCE

10) Turn off all 8 switches on DIPSW1

This completes the re-calibration where the control board has not been removed or replaced

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Acroprint Système de sécurité

Acroprint

Acroprint ATRx ProxTime Manuel utilisateur

Acroprint

Acroprint ATRx Biometric 1000 Manuel utilisateur

Acroprint

Acroprint Time Q +Plus Manuel utilisateur

Acroprint

Acroprint BioTouch Manuel utilisateur

Acroprint

Acroprint ARES IV Manuel utilisateur

Acroprint

Acroprint ARES III Manuel utilisateur

Acroprint

Acroprint ATRx Biometric 1000 Manuel utilisateur

Acroprint

Acroprint TimeQ+ Biometric Manuel utilisateur

Acroprint

Acroprint ATRx Secure PunchIn Manuel utilisateur

Acroprint

Acroprint FaceVerify TQ600F Manuel utilisateur

Acroprint

Acroprint ATRx Secure PunchIn Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur