ACR Electronics ResQLink PLB-375 Instructions d'installation

406 MHz Personal Locator Beacons

PRODUCT SUPPORT MANUAL

Model: PLB-375 / Product No.: 2880

Y1-03-0251 Rev. C

Cobham Beacon Solutions

5757 Ravenswood Road

Fort Lauderdale, FL 33312

www.acrelectronics.com

PLEASE READ ALL WARNINGS, CAUTIONS AND NOTES

CARFULLY

CAUTION: Before proceeding to test or use your new ACR

Electronics’ product, please read this Product Support

Manual in its entirety.

WARNING: The PLB must be promptly registered with the

appropriate National Authority. Failure to register the PLB

could delay a Search and Rescue (SAR) response and may

be unlawful.

WARNING: This transmitter is authorized for use only

during situations of grave and imminent danger. Deliberate

misuse may incur a severe penalty.

CAUTION: False alerts endanger lives and cause expensive

disruption to Search and Rescue services, deliberate misuse

of the PLB could result in penalty and fine.

CAUTION: Contains lithium batteries. Do not incinerate,

puncture, deform, short-circuit or recharge.

CAUTION: Do not dismantle the PLB, contains no user-

serviceable parts.

CAUTION: Remove from pouch prior to operation

Disposal: Remove the Lithium battery. Dispose of the used

battery in accordance with local waste disposal regulations.

Air Travel: Product contains small lithium metal batteries

that comply with IATA SP 188-PI 970 Air Cargo. Always

check with air carrier concerns for any additional

restrictions.

This manual supports all configurations of PLB-375 beacons. In addition

to the part numbers listed on the cover page, other configurations of

these products may be available, thus you may have purchased a

product configuration with a different version of the part number (for

example, 2880.63). As long as the first four digits are the same as one

of the part numbers on the cover, this manual is applicable. If you have

questions regarding the contents of the manual or something not

covered in the manual, please contact our Technical Service

Department at ACR Electronics Inc. +1 (954)-862-2110.

Table of Contents

1. Registration 3

2. Anatomy Of A Rescue 6

3. Anatomy Of Your Beacon 7

4. Activating Your Beacon 8

5. Turning Your Beacon Off 11

6. Testing Your Beacon 12

7. Satellite Testing 14

8. Preventing False Alarms 15

9. Beacon Maintenance 16

10. Product Specifications 18

11. Product Warranty 19

Table Of Contents & Warnings

REGISTERING YOUR BEACON

Why is registration important?

As the owner of this 406 MHz beacon, it is a

requirement that you register it with the

National Authority of your country. Please note

that in many countries all 406 MHz beacons are

required to have their registration updated every two

years by the owner. Please check the requirements

for your country of registration.

HOW REGISTRATION WORKS:

All 406 MHz beacons transmit a Unique Identifier

Number (UIN) when activated. This UIN is

programmed into the beacon based on the country in

which the beacon is registered, thus authorities are

able to determine which country’s database will have

your registration information. Search and Rescue

(SAR) forces will have information as to who you are

as the owner of the beacon, the name and type of

vessel that you have (if applicable), your address,

and who to contact that might know of your current

situation - but only if your beacon has been properly

registered. Valuable search and rescue resources are

wasted every year responding to false alerts, and

registering your beacon helps to resolve this quickly.

1. Registration

What country should I register in? The beacon must be registered in the

country of the owner’s residence. If the beacon is not programmed to that

country’s code and protocol, and the residence is outside of the USA, the

beacon needs to be reprogrammed.

Additionally, the beacon must be reprogrammed if you, as the owner, move out

of the country where the beacon is registered. To verify the country for which a

beacon is programmed, see the label with the UIN (Unique Identification

Number) on the back of the unit.

For a complete list of all countries with online registration links visit

www.acrelectronics.com/support/registrations/

Please check to make sure that your PLB is registered correctly

How do I register?

Registration in the United States - The national authority that accepts

registrations in the United States is the National Oceanic and Atmospheric

Administration (NOAA).

All registration forms will be entered in the 406 MHz beacon registration

database within 48 hours of receipt. The information you provide on the

registration form is used for rescue purposes only.

A confirmation letter, a copy of the actual registration and a proof-of-registration

decal will be mailed to you within two weeks. When you receive these

documents, please check the information carefully, and then affix the decal to

your beacon in the area marked “BEACON DECAL HERE.”

It is very important that the proof of registration decal matches the UIN on the

beacon. If you do not receive confirmation back from NOAA within two weeks,

call toll free (888) 212-7283 for assistance.

User Tip

The fastest and easiest way to

www.beaconregistration.noaa.gov/

Or Mail To:

SARSAT Beacon Registration NOAA

NSOF, E/SP053

4231 Suitland Road

Suitland, MD 20746

Or Fax To:

Faxing a registration is also acceptable.

Fax the registration form to 301-817-

4565

Registration in Canada

Canadian residents can register online at:

International customers should visit

http://www.acrelectronics.com/support/registrations/

to find the proper location to register your beacon.

The fastest and easiest way to register

is online at:

http://canadianbeaconregistry.forces.gc.ca/

Or Mail To:

Canadian Beacon Registry

CFB Trenton, PO Box 1000 Stn Forces,

Astra, Ontario K0K 3W0

Or Fax To:

Faxing a registration is also acceptable. Fax

the registration form to 877-406-3298

Registration in Other Countries

In countries other than the United States and Canada,

406 MHz beacons are registered with that country’s

national authority at the time of purchase. The sales

agent may have assisted you in filling out the forms and

sending them to the country’s national authority.

To verify that the unit is properly programmed for your

country, view the UIN label on the back of the unit. In

the event that the beacon is not programmed for your

country, the sales agent (if properly equipped) can

reprogram the unit for the correct country.

1. Registration

HOW THE BEACON WORKS

How your beacon summons help

406 MHz beacons are a type of portable emergency equipment that

transmits a distress signal to search and rescue (SAR) organizations. The

purpose of these beacons is to aid SAR teams in tracking and locating

ships or individuals in jeopardy as rapidly as possible.

The 406 MHz frequency is a worldwide dedicated emergency frequency

that is detected by a network of satellites called the Cospas-Sarsat

system. This satellite system was established by, and continues to be

supported by, its primary benefactors - the USA, Russia, Canada and

France. The Cospas-Sarsat system has saved over 30,500 lives - and

counting - since its inception. To learn more about the system visit

www.cospas-sarsat.org.

When a 406 MHz beacon is activated, the digital distress message is sent

to Cospas-Sarsat satellites and, in turn, the distress message is relayed

to SAR forces. The distress message contains the beacon UIN and on

some models the GPS location of the beacon. Additional information

about the beacon is accessed by SAR forces from the beacon registration

database. At the same time the 406 MHz signal is activated, a 121.5 MHz

signal is turned on. The 121.5 MHz signal is used by SAR forces to home

in on the beacon as they approach it.

The 406 MHz signal is detected by multiple satellites and from that

information the location of the beacon can be calculated. This data alone

is sufficient for SAR to find persons or ships in distress in a reasonable

timeframe. However, as a further enhancement, some beacons have a

GPS engine onboard. This feature allows the beacon to acquire current

location coordinates from an internal GPS receiver. The purpose of this

feature is to send an even more precise location of the beacon to the

satellites, i.e., latitude and longitude data. This helps SAR to reach the

location even faster. 6

2. Anatomy Of A Rescue

User Tip

Learn more about the Cospas-Sarsat satellite

system: www.cospas-sarsat.org

Warning: This transmitter is authorized for use only

during situations of grave and imminent danger.

Deliberate misuse may incur a severe penalty.

3. Anatomy Of Your Beacon

Anatomy of your beacon

A. Antenna Latch –Latch unlocks antenna from beacon body. When unclipped, the antenna

can be deployed to uncover On/Off and test buttons.

B. Strobe Light –Activates when beacon is turned on and at the end of each self test.

C. Green LED Light –Visual indicator of beacon activity.

D. Red LED Light –Visual indicator of beacon activity.

E. GPS Receiver –Location of GPS Receiver, give clear view to sky and do not obstruct.

F. ON/OFF Button –Activates the beacon when pressed for 1 second. Turns beacon off when

pressed for 3 second. (button is embossed only, red color is for enhanced graphics

presentation)

G. TEST Button –Self Test Beacon to do full function test.

H. Antenna –Wraps around product and protects On/Off and Test Buttons.

I. Lanyard –Secures beacon to prevent loss.

Overview

Personal Locator Beacons are designed to be manually activated. They

are only to be activated when all other means of self-rescue have been

exhausted. When properly registered as required, the activation of the

beacon tells Search and Rescue who you are, where you are, and that

you are facing a life threatening situation.

How To Activate Your Beacon

To activate your beacon in a distress situation, follow these steps:

1. Unclip the antenna latch from the case and move

antenna into the upright position

2. Depress the ON/OFF button for 1 full second. (button is

embossed only, red color is for enhanced graphics presentation)

When Activated (First Minute):

To let you know the beacon has been activated, you will see the strobe

light flash once every second while the RED light will flash once every 3

seconds.

After the First Minute:

While transmitting your distress signal, the RED light and Strobe light

each will flash once every 3 seconds, alerting you that your beacon is

active.

When the Red light is replaced by the GREEN light, this indicates that

your beacon has successfully downloaded your GPS coordinates and is

transmitting them along with your 406 MHz Distress Signal.

4. Activating Your Beacon

Activation with GPS

When your unit is activated, the GPS receiver will turn on, search to find your LAT/LON and

incorporate it into your 406 MHz signal. As soon as the GPS receiver acquires valid positioning

data, the red flashing light will be replaced by a green flashing light once every 3 seconds.

The same GPS data will be sent with each 406 MHz signal for the next 30 minutes. At that

time the internal GPS will start up again, search to find your LAT/LON and incorporate it into

your next 406 MHz signal. If for any reason the internal GPS cannot update your LAT/LON,

your last position will be used for the next four hours. At that time the green LED will stop

blinking and the red LED will flash once every 3 seconds until new GPS data is obtained.

GPS receiver orientation

When activated, it is critical that you do not cover the beacon with any body part, water,

clothing, etc. The GPS receiver is located under the bottom portion of the case where it is

outline with the text “GPS, Give Clear View To Sky.”

To ensure optimum performance of the GPS receiver, the beacon needs to have an

unobstructed view of the sky. Avoid submerging the GPS receiver in water if possible. Water

will shield and inhibit the GPS receiver and may cause difficulties obtaining your GPS

coordinates. Avoid leaning over the beacon to view blinking LED as you may shield the GPS

reception.

4. Activating Your Beacon

Red Flashing Light =

Sending 406 MHz

Signal Only

Green Flashing Light =

Sending 406 MHz

Signal with GPS

Coordinates

Proper Positioning and Handling during Activation

4. Activating Your Beacon

Make sure the antenna is pointing towards

the sky, out of the water. Beacon is not

intended to operate in water.

Do not cover the GPS receiver with your

hand and make sure you have a clear view

to the sky to ensure GPS is downloaded.

Autres manuels pour ResQLink PLB-375

Table des matières

Autres manuels ACR Electronics Capteur de sécurité

ACR Electronics

ACR Electronics COBHAM RCL-300A Instructions d'installation

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur