Acnodes RMC8416 Manuel utilisateur

For lastest product information, please visit Acnodes’ website at www.acnodes.com

14628 Central Ave. Chino, CA 91710 Tel: 909.597. 7588 Fax: 909. 597.1939

INSTALLATIONSTEPS

To install the RMC 8416 chassis, the following installation

steps must be completed:

Step 1: Unpack the chassis.

Step 2: Install the front handles.

Step 3: Remove the top cover and hold-down clamp.

Step 4: Install the PSU.

Step 5: Install the backplane.

Step 6: Install the CPU card.

Step 7: Install the PCI and ISAexpansion cards.

Step 8: Install the disk drives.

Step 9: Connect front panel cables.

Step 10: Connect PSU cable and interface cable.

Step 11: Install the hold-down clamp and PCI/ISA

card shock absorbers.

Step 12: Reinstall the top cover.

The installation steps outlinedabove are described in

detail below. Please refer to the relevant section.

STEP 1: UNPACK

The RMC 8416 is shipped in a plastic bag that is placed

inside acardboard box. The items are also shipped with

the chassis. When you unpack the chassis you must:

Make sure all the items listed above are present.

Make sure the chassis has not been damaged in any

way.

STEP2:FRONT HANDLEINSTALLATION

Two handles are shipped with the RMC 8416 chassis. The

handles are installed on the sides, at the front of the

chassis. Each handle is secured to the chassis by 4

retention screws. To install the handles, please follow the

steps below:

Step 1: Align the retention screw holes on the side of the chas-

sis with the retention screws in the handle.

Step 2: Insert 4 retention screws for each handle.

Figure 2: Insert 4 Front Handle Retention Screws

STEP3: TOP COVERAND HOLD-DOWN CLAMPREMOVAL

3.1:TOPCOVERREMOVAL

The top cover is secured to the chassis with 6 retention screws,

three on each side of the chassis. To remove the top cover, please

follow the steps below:

Step 1: Remove all 6 top cover retention screws. Remove 3

retention screws from each side of the chassis.

Figure3:TopCoverRetentionScrews

Step 2: Slide the top cover backwards and Lift the top cover up

gently.

STEP 3.2: HOLD-DOWN CLAMPREMOVAL

Detach the hold-down clamp byremoving the 2 screws located on each side of the chassis and lift the hold-down clamp off

the chassis.

Figure 5: Remove the2Hold-Down Clamp Retention Screws

Figure 6: Lift the Hold-Down Clamp off the Hold-Down

ClampSecuringHook

STEP 4: Install the Power Supply Unit (PSU)

Once the top cover and hold-down clamp have been removed, the PSU must be installed. Compatible IEI PSUs are listed in

the table below.

Table 2: Compatible IEI PSUs.

15-inch touch panel PC

The PSU is installed at the rear of the chassis. The PSU

is secured to the chassis with an internal PSU securing

clamp and 4 retention screws from the rear of the chassis.

To install the PSU, please follow the steps below:

Step 1: To remove the PSU securing clamp, remove the

2 PSU securingclamp retention screws.

Figure 7: PSU Securing Clamp Retention Screws

Step 2: Correctly position the PSU at the rear of the

chassis making sure that the power switch and the cable

socket both face outwards.

Step 3: Once the PSU has been correctly positioned,

secure the PSU to the chassis by inserting 4 retention

screws through the rear of the chassis.

Figure 8: Insert PSU Retention Screws

Step 4: Reinstall the PSU securing clamp and

reinsert the 2 previously removed PSU securing

clamp retention screws.

STEP5:BACKPLANEINSTALLATION

The IEI backplanes listedbelow are compatible with the

RMC 8416 chassis.

Table3:CompatibleBackplanes

To install a compatible backplane please follow the

instructionsbelow:

Step 1: Insert the copper pillars in the predrilled screw

holes in the bottom of the chassis according to the

distribution of the retentionscrew holes in the backplane

you want to install.

Figure9: Locations of the 9 Copper Pillars

Step 2: Mount the backplane onto the copper pillars and

align the backplane screwholes with the screw holes in

the copper pillars.

Step 3: Once the backplane is properlyaligned with the

retention screw holes, insert retention screws in all the

retention screwholes in the backplane to secure the

backplane to the chassis.

Figure10: InsertBackplaneRetentionScrews

STEP6:CPUCARDINSTALLATION

To install the CPU card please follow the instructions

below:

Step 1: Remove the slot cover at the front of the chassis.

To do this, remove the slot cover retention screwat the top

of the slot cover.

Figure 11: Remove the SlotCover Retention Screw

Step 2: Slide the CPU card into the socket on the

backplane reserved for the CPUcard. If you are installinga

full-size CPU card, make sure the back edge of the CPU

card slots into the corresponding plastic guides located

behindthe coolingfans.

Step 3: To secure the CPU card, reinsert the previously

removedslotcoverretentionscrew.

STEP 7: PCI/ISAEXPANSION CARD INSTALLATION

The RMC8416 supports upto13 PCI/ISAexpansion

cards. To install an expansion card (PCI or ISA) please

follow the steps below.

Step 1: Remove the slot cover at the back of the chas-

sis. To do this, remove the slot cover retention screw at

the top of the slot cover.

Step 2: Slide the PCI/ISAexpansion card into reserved

PCI/ISA socket on the backplane.

Step 3: To secure the PCI/ISA expansion card,

reinsert the previouslyremoved slot coverretentionscrew.

STEP 8: DISK DRIVES INSTALLATION

The RMC 8416 chassis has 2 drive brackets: a main drive

bracket and a side bracket. To installthe drives, please

follow the steps outlined in the sections below.

STEP8.1:REMOVETHESIDEBRACKET

Before anydrives can be installed, the side bracket

attached to the maindrive bracket must be removed.To

remove the side bracket,removethe2 retention screws

from the top of the side bracket that secure the side

bracket to the main bracket.

Figure12:RemovetheSideBracket

STEP 8.2: 3.5" DRIVE INSTALLATION INTO THE

SIDEBRACKET

The side bracket supports one 3.5" drive. If you want to

install a 3.5" drive into the side bracket, please follow the

steps below:

Step 1: Place a 3.5" FDD drive into the bracket. Make

sure the FDD PCB board is facing the surface of the

bracket and the 4-pin power connector and the IDE/SATA

interfaceconnectorare facingtherear of the bracket.

Step 2: To secure the 3.5" HDD to the side bracket,

insert 4 retention screws, two on each side.

Figure13: Insert4HDD Retention Screws

STEP8.3:REMOVETHEMAIN DRIVEBRACKET

If you wish to install a 5.25" opticaldrive or more than one

3.5" drive (HDDor FDD), the main drive bracket must be

removed.Toremovethemaindrivebracketfromthe

chassis, follow the steps below:

Step 1: Remove the side bracket (See STEP 8.1:

REMOVETHESIDEBRACKETabove).

Step 2: Remove the 4 retention screws that secure the

main drive bracket to the base of the chassis.

Figure 14:Remove the 4 Main Bracket Retention Screws

STEP 8.4: 3.5" DRIVE INSTALLATION IN THE MAIN

DRIVEBRACKET

Themaindrivebracketsupportsone5.25" opticaldriveand

one 3.5" drive (FDD or HDD). If you want to install a 3.5"

drive (FDD or HDD) into the maindrive bracket, please follow

the steps below:

Step 1: Remove the front metal cover from the 3.5" drive

baybyremoving the 2 front cover retention screws on both

sides, one on each side, of the 3.5" drive bay.

Figure15:RemovetheFrontMetalCoverRetentionScrews

Step 2: Slide a 3.5" drive into the 3.5" drive bay. Make sure

the driveis upright and the 4-pin power connector and the

IDE/SATAdrive interfaceconnector are attherear of thedrive

bay.

Step 3: Secure the 3.5" drive to the drive bay by

inserting 4 retention screws, two on each side, through the

sides of the main drive bracket and into the 3.5" drive.

Figure 16:InsertFour 3.5”Drive RetentionScrews

STEP 8.5: 5.25" DRIVE INSTALLATION IN THE MAIN

DRIVEBRACKET

If you want to install a 5.25" optical drive into the main

drivebracket,followthesteps below:

Step 1: Remove thefront metal cover from the 5.25" drive

baybyremoving the 4 front cover retention screws, on

both sides, two on each side, of the 5.25" drive bay.

Figure 17: Remove the4 Retention Screws on the Sides

of the Main Bracket

Step 2: Slide a 5.25" optical drive into the drive bay.

Makesurethe4-pinpowerconnector andtheIDE/SATA

driveinterface connector arefacingtherear of the chassis.

Step 3: Secure the 5.25" optical drive to the drive bay by

inserting 4 retention screws (two on each side) through the

sides of the drive bracket and into the 5.25" optical drive.

Figure 18: Install a 5.25" Disk Drive into the Main Drive

Bracket

STEP8.6:REINSTALLTHEDRIVEBRACKETS

Once allthe drives have beeninstalled intothedrive

brackets, reinstall the drive brackets into the chassis. To

reinstall the drive brackets into the chassis, please follow

the steps below:

Step 1: Place the main drive bracket into the chassis

making surethat the front of the 5.25" optical drives are

facing out of thechassis and the4-pin drive power connec-

tors andIDE/SATAinterfaceconnectors are all facing the

rear of the chassis.

Step 2: Reinsert the 4 previously removed main drive

bracket retention screws.

Step 3: Correctlymount the side drive bracket onto the

main drive bracket making surethe4-pin power connector

and IDE/SATAinterface connectorboth face the rearof the

chassis; and the clip at the bottom of the internal HDD

bracket slots into the space between the clip on the right

side of themain drive bracket and the main drive bracket.

Figure 19: Clips Locations

Step 4: Reinsert the 2 previouslyremoved side bracket

retention screws into the top of the side bracket.

STEP9: CONNECT FRONT PANELCABLES

The RMC 8416 has LEDs, buttons and ports on the front

bezel.

o 1 x Power LED

o 1 x HDD activity LED

o 1 x Power switch

o 1 x Reset button o 2 x USB ports

These components are all connected to the CPUcard with

cables. To correctlyconnect these cables, please refer to

the technicaldocumentation that came with your CPU

card. The connectors that are provided with the chassis

are listed below.

Table 4: Chassis Connectors

The pin definitions for the USB cableare shown below

STEP 10: PSUCABLEAND INTERFACE CABLECON-

NECTIONS

Beforeyoureinstall thehold-downclamp and thecover,

the following cables need to be connected.

Step 1: Connect the PSU cables from the PSU to the

backplane, full-size CPU card, HDD, FDD, cooling fans

andopticaldrivespowerconnector.

Step 2: The drive interface connectors must be con-

nected to the CPU card.

STEP11: HOLD-DOWN CLAMPAND PCI/ISACARD

SHOCKABSORBERSINSTALLATION

The RMC 8416 comes with9 shock absorbers, 2 long

shock absorbers and 7 short shock absorbers, used for

securingthe PCI/ISAcardsfrom vibration. Becausethe

shock absorbers are attached to the hold-down clamp, the

shock absorbers should be installed after hold-down

clamp is reinstalled. To install the hold-down clamp

and shock absorbers, please follow the steps below:

Step 1: Slide the end of the hold-down clamp with 2

holesfor the hold-down clamp hooks into the hold-down

clamp securing hook on the right side of the chassis.

Step 2: Align the retention screw holes in the other

end of the hold-down clamp with two retention screw holes

in the clip stretches out from the internal side HDD

bracket.

Figure 20: Hold-Down Clamp RetentionScrewHoles in the

Clip of the Side HDD bracket

Step 3: Reinsert the 2 hold-down clamp retention screws.

Step 4: Press the rubber of a shock absorber with proper

length against the top of the PCI/ISA card you want to

secure, according to the height of the installed PCI/ISA card.

Step 5: Align the retention screw hole in the shock

absorber with the correspondingretention screwhole in the

hold-downclamp.

Step 6: Insert one retention screw for each shock

absorber to secure itto the hold-down clamp.

Figure 21:PCI/ISACardShockAbsorber

STEP12: COVER REINSTALLATION

Afteryouhavecompletedtheaboveprocedures,thecover

can be reinstalled. To do this, slide the cover back over the

chassis and reinsert the6previouslyremoved retention

screws.

There are three 8 cm cooling fans insidethe RMC 8416

chassis. To replace a fan, please followthe instructions

below:

Step 1: Loosen 2 thumbscrews for the fan that must be

replaced.

Figure 22: Locations of the Fan Bracket Thumbscrews

Step 2: Unplug the power cable that is connected to the

fan.

Figure 23: Unplug the Fan Power Cable

Step 3: Remove the fan byremoving thefour fan retention

screws.

Figure 24:RemovetheFan RetentionScrews

Step 4: Replace the fan and secure a new fan to the fan

bracket with the4 previouslyremoved retention screws.

Step 5: Reinstall the fan bracket into the chassis and

secure it to the chassis with the 2 previouslyloosened

thumbscrews.

FANFILTERREPLACEMENT

To replace the fan filter, please follow the steps below:

Step 1: Loosen the 2 fan filter bracket retention screws at

the top of the fan filter bracket and open the bracket.

Figure 25:Remove the Fan Filter

Step 2: Replace the fan filter pad inside.

Step 3: Reinstall the fan filter bracket and secure it to the

chassis withthe 2previouslyremoved retention screws.

CABINETINSTALLATION

Supporting rails, rack trays, or slide rails can be imple-

mented using the mounting holes on the sides of the

chassis. The four mounting holes in the two handles on the

sides of the chassis are used to secure the chassis to the

front rack posts in your rack cabinet to prevent the chassis

fromfallingforwards.

Figure 26: Locations of the 4 Mounting Holes

Table des matières

Autres manuels Acnodes Ordinateur de bureau

Acnodes

Acnodes LW 6150 Manuel utilisateur

Acnodes

Acnodes LW 846 Manuel utilisateur

Acnodes

Acnodes FES7501 Manuel utilisateur

Acnodes

Acnodes RMC 7217A Manuel utilisateur

Acnodes

Acnodes RMC 6125A Manuel utilisateur

Acnodes

Acnodes RMC 7312A Manuel utilisateur

Acnodes

Acnodes FPC 8121 Manuel utilisateur

Acnodes

Acnodes RMC 6446B Manuel utilisateur

Acnodes

Acnodes LW 6120 Manuel utilisateur

Acnodes

Acnodes RMC 3012A Manuel utilisateur

Acnodes

Acnodes RMC 6121B Manuel utilisateur

Acnodes

Acnodes RMC 7150X Manuel utilisateur

Acnodes

Acnodes LW 910 Manuel utilisateur

Acnodes

Acnodes RMC 6343A Manuel utilisateur

Acnodes

Acnodes LW 846 Manuel utilisateur

Acnodes

Acnodes FES 8000 Manuel utilisateur

Acnodes

Acnodes RMC 6224A Manuel utilisateur

Acnodes

Acnodes FES2215 Manuel utilisateur

Acnodes

Acnodes FES 9000 Manuel utilisateur

Acnodes

Acnodes RMC 6220B Manuel utilisateur

Acnodes

Acnodes RMC 7212A Manuel utilisateur

Acnodes

Acnodes LW 922 Manuel utilisateur

Acnodes

Acnodes RMC 6220A Manuel utilisateur

Acnodes

Acnodes PLW 8150 Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur