ACL Staticide IONA TECH StatIQ Band Manuel utilisateur

Ph: +1-847-981-9212 Email: [email protected]

User Manual

DISCLAIMER

Please read the following disclaimer carefully before using the StatIQ Band (the "Product"),

produced by IONA Tech (the “Company”). By using the Product, you (the “Customer”)

acknowledge and agree to the terms and conditions outlined below:

The Product is designed to help prevent electrostatic discharge damage in industrial

environments. However, it is important to note that the industrial environment is complex and

can involve numerous variables beyond our control. Therefore, the Company cannot

guarantee complete prevention of electrostatic discharge or damage to equipment or

systems.

The Product is provided "as is" and without any warranties, express or implied. The Company

makes no representations or warranties regarding the effectiveness or suitability of the

Product for any specic application or environment. It is the Customer’s responsibility to

assess and determine the appropriateness of the Product for their particular needs.

While the Product is designed to function under normal operating conditions, there may be

situations where it may fail to operate as intended without warning. This could result in

equipment damage, malfunction, or other adverse effects. The Company shall not be held

liable for any such damages or malfunctions.

It is crucial to follow all installation, operation, and maintenance instructions provided with the

Product. Failure to do so may result in improper functioning and potential damage to

equipment or systems. The Company shall not be responsible for any damage caused by

improper use, installation, or maintenance of the Product.

The Product is not intended to replace or substitute for any safety measures, protocols, or

regulations mandated by applicable laws or industry standards. The customer is responsible

for ensuring compliance with all relevant safety guidelines and regulations in your industry.

To the maximum extent permitted by law, the Company disclaims all liability for any direct,

indirect, incidental, consequential, special, or punitive damages arising out of or in connection

with the use or inability to use the Product, even if the Company has been advised of the

possibility of such damages.

The customer agrees to indemnify and hold the Company harmless from any claims,

damages, liabilities, costs, or expenses (including attorneys' fees) arising out of or in

connection with the use or misuse of the Product.

This disclaimer shall be governed by and construed in accordance with the laws of the state of

Colorado in the USA. Any legal action or proceeding arising out of or relating to this disclaimer

shall be brought exclusively in the courts of the state of Colorado in the USA.

By using the Product, the Customer acknowledges that they have read, understood, and

agreed to the terms and conditions of this disclaimer. If the Customer does not agree with any

part of this disclaimer, they should refrain from using the Product.

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

StatIQ Band:

A Wearable Body Voltage Monitor

Table of Contents

Getting Started ................................................................................................................................................. 3

Operation..............................................................................................................................................................4

IONA Tech App.................................................................................................................................................. 7

Usage Details.................................................................................................................................................... 10

Troubleshooting..............................................................................................................................................15

Applications....................................................................................................................................................... 18

Technical Specications .............................................................................................................................19

Warranty Information ................................................................................................................................ 20

Regulatory and Safety Notices...............................................................................................................21

Get in Touch ..................................................................................................................................................... 24

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Getting Started

In the StatIQ Band box you will nd

•The StatIQ Band, with hook-and-loop arm strap

•A Zero Disc for rapid, one-handed zeroing of the StatIQ Band

•A USB-C charging cable

•A Quickstart Guide

•A Calibration Certicate for your StatIQ Band

Charging

Before you begin using the StatIQ Band, make sure the battery is fully charged. To

charge the battery:

1. Locate the USB-C charging port on the bottom edge of the device.

2. Plug the provided charging cable into any USB power source.

3. While charging, the Charging LED will be amber.

4. When the Band is fully charged, the charging LED will turn green.

5. The Band may take as long as an hour to charge, if completely at.

6. The battery life of the Band in use is 12-16 hours.

Sensor Protection

On delivery, the sensor will be

covered by a removable sticker.

Take this sticker off before

using the device. Do not stick

your ngers or other objects

into the sensor port, ever.

Doing so may lead to damage

or contamination of the sensor,

which is not covered under the

warranty.

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Operation

These pictures show the arrangement of the Band’s indicators and button.

Wearing the StatIQ Band

Secure the StatIQ Band around your upper arm in the orientation shown, ensuring

that the sensor is unobscured and pointed away from your body. The band should

be as high up your arm as possible.

Make sure to wear conductive or static

dissipative clothing such as an ESD rated

smock. Synthetic clothing will hold localized

charge that results in an offset in the voltage

measurement and undetected ESD events.

Ensure that you can see the three LEDs on the

upper edge of the device (the Mode, Body

Voltage and Bluetooth LEDs), and that the gold

sensor is situated above the Power/ Mode

button and the IONA logo.

Fasten the hook-and-loop strap just tightly

enough that the Band does not slip down your

arm, but not so tight as to be uncomfortable.

You may need to stretch your sleeve towards your hand before tightening the strap,

to ensure there are no folds of clothing covering the sensor.

Device ID

Power/Mode

Button

Charging

LED

Sensor

Ground Point

Socket

USB C

Connector

Bluetooth

LED

Power &

Mode LEDs

Body Voltage

LED

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Turning the StatIQ Band ON

Hold the Power/Mode button until the StatIQ Band turns ON. A similar press will

turn the StatIQ Band OFF.

The eld mill sensor will begin spinning and the device is now measuring the local

electric eld. If secured to your arm, this measurement represents an accurate

measure of your body voltage.

The Body Voltage LED indicates whether you are charged positive (red) or negative

(blue) and its brightness indicates the measured voltage relative to the alarm

threshold (discussed later).

Body voltage LED:

Red = Positive body voltage. Voltage below threshold

Blue = Negative body voltage. Voltage below threshold

Changing Alarm Modes

A short press of the Power/Mode Button will switch the band between the Muted

and Audible modes.

Power/Mode LED:

Yellow = device muted.

Green = audible alarms enabled.

The Power/Mode LED is visible both on the top edge of the StatIQ Band as well as

on the lid next to the Power/Mode Button.

Audible Alarms

Constant alarm = body voltage past threshold (only if audible alarms enabled)

Three quick beeps = ESD event detected (only if audible alarms and ESD Event

Detection enabled).

Single beep with Orange Power/Mode LED ash = low battery.

Four beeps with Red Power/Mode LED ash = empty battery, device powers off.

Continuous quick beeps with Red Power/Mode LED ash = shutter malfunction

(see Troubleshooting section).

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Default Settings

The StatIQ Band is intended to be usable out of the box, with no conguration

necessary. It is calibrated and zeroed in production. The default settings are:

Audible Alarms – muted (to be changed by pushing the Power/Mode button)

Alarm Threshold – ±1000V

Alarm Volume – 50%

ESD Event Detection – Enabled

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

IONA Tech App

Download the IONA Tech App from the App Store or

Google Play Store to visualize the measured voltage data,

change device parameters, and more.

Pairing a Device

When you start the app, the following screen appears.

Select the Device that matches the address printed on

the label on the side of your StatIQ Band.

Note that when a device is paired with one app, it

cannot at the same time pair with another app on

another phone or PC.

The Bluetooth LED on the top edge of the StatIQ Band

will illuminate blue when the device is connected to an

app.

StatIQ Band paired with app

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

StatIQ Band Data

Once you have paired with a device, the app will display

a real time graph of the voltage and events from that

device.

ESD Events will display on the graph as red dots, where

the position on the y-axis represents the voltage

change of the discharge.

Change the time scale above the graph to assess

various lengths of voltage data.

Select ‘Record Session’ to generate a CSV le of the

voltage and ESD data from the session. The le will be

generated in the Documents folder of your phone:

1. When you press ‘Save Recording’

2. If you close the connection by returning to the

Device List screen

3. If the connection is lost because the StatIQ Band

is turned off or if it goes out of range.

Device Conguration

Select the Gear icon on the previous page to adjust the

following options:

1. Voltage Threshold – the body voltage at which

the alarm will sound (the level is the same for

positive and negative voltage deviations).

2. Alarms Audible – checking this box changes the

device mode from Muted to Audible. The mode

can still also be changed by the Power/Mode

button on the device.

3. Alarm Volume – adjusts the alarm volume.

4. ESD Event Detection – checking this box

ensures that the StatIQ Band detects ESD

discharge events. Note that an audible alarm will

sound for ESD events only if Alarms are set to

Audible.

Record Session

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Unpairing a Device

Note that the Band will remain paired with the app, even if that app is not open on

the home screen of the phone. The Band can be unpaired by clicking “change

device” or pressing the back arrow from the voltage screen. A conrmation dialog

will appear before the connection is closed.

IONA Tech Browser App

All the functionality of the mobile apps can be achieved on a Chrome browser from

any computer equipped with a Bluetooth radio. Simply direct your Chrome browser

to:

https://app.iona.tech/

Distributed by ACL Staticide: +1-847-981-9212 Email: [email protected]

Table des matières

Manuels Électricité industrielle populaires d'autres marques

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manuel technique

Abtech

Abtech HVJB Series Mode d’emploi

Murata

Murata GRM0335C1H8R1DA01 Series Manuel utilisateur

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manuel utilisateur

Eaton

Eaton Ulusoy HMH24-04 Manuel utilisateur

Newlong

Newlong NP-7H Manuel utilisateur

Murata

Murata GJM0335C1E4R4BB01 Series Manuel utilisateur

Stahl

Stahl 8575/12 Manuel utilisateur

SI Pegasus Manuel utilisateur

Murata

Murata GRM1555C1H2R7CA01 Seies Manuel utilisateur

Murata

Murata GRM0225C1E6R4BA03 Series Manuel utilisateur

Cooper Power Systems

Cooper Power Systems VXE15 Manuel utilisateur

S&C

S&C Vista SD Manuel utilisateur

Murata

Murata GRM0335C2A7R3CA01 Series Manuel utilisateur

Siemens

Siemens 3VA9988-0BM10 Manuel utilisateur

Siemens

Siemens SITRANS LVS100 Manuel utilisateur

Murata

Murata GRM32ER60G227ME05 Series Manuel utilisateur

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manuel utilisateur