Ace 598-1214-03 Manuel utilisateur
© 2007 598-1214-03
Remote
ContRolled
PRoduCts
This manual includes operating instructions for
the remote controlled products shown above. All
products work on the same principle and use the
same code setting information. Please read all
instructional information and note any specific
information pertaining to your particular product.
FEATURES
• Products are UL/cUL and/or FCC/IC tested and
approved.
• Operational range of up to 100 feet.
ACE®wireless lighting controls are designed
to work together. Simply determine which
transmitter(s) you would like to have controlwhich
receiver(s) and set the code setting to match.
Wireless
Motion
Sensor
Floodlight
Converter
Indoor
Plug-In
Converter
Lamp
Socket
Converter
Remote
Control
2598-1214-03
CODE SETTINGS
Note: Most single system installations will
not require any change to the code setting.
Transmitter(s) and receiver(s) must have
the same code and group setting to work
together.Switches 1 through 3 set the code.
Switch 4 sets the Group (A or B). See Code
Switch Locations for switch locations.
Transmitter(s)/
Receiver(s) Code
Group B
Transmitter(s)/
Receiver(s) Code
Group A
Example 1 - Code Switch Settings, System 1
(Factory Setting)
ON
1 2 3 4
ON
1 2 3 4
WARNINGS
• FOR USE ONLY with 120 volt incandescent
or halogen bulbs.
• DO NOT USE with fluorescent bulbs, appli-
ances, power supplies, low voltage lighting, or
any other electrical devices.
( – Indicates Position of Switch)
3
598-1214-03
Note: When operating more than one system
independently of each other, set each system to
a different code. There are 8 codes available by
changing the settings of switches 1 through 3.
Example 2 - Code Switch Settings, System 2
Receiver(s)
Code
Group A
Transmitter(s)
Code
Group Switch
(Group A Selection Shown)
Example 3 - Code Switch Settings with Single
Transmitter
Receiver(s)
Code
Group A
Remote Motion
Sensor Code
When using the wireless motion sensor, the code
and group settings must match receiver(s) for the
system to function properly.
Note:This setting will work independently of exam-
ples 1 and 2 because the code setting is different.
Note: The channel can also be changed to reduce
interference problems from other wireless products
(i.e. wireless phones, garage door openers, etc.). See
Troubleshooting Guide for more information.
Group A
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
4598-1214-03
Floodlight
Converter
Wireless Motion
Sensor
CODE SWITCH LOCATIONS
Code Switches
Close-Up of Typical Code Switch
(Factory Default Setting is Off)
Note: The “X” has been placed on the
switches to help clarify the illustra-
tions under Code Settings.
DETECT
CODES
1234
DAY
NIGHT
NIGHT
ONLY
ON
1 2 3 4
12 3 4
ON
1 234
Lamp Socket
Converter
Indoor Plug-In
Converter
Code Switches
ON DIP
1 2 3 4
ON DIP
1 2 3 4
Remote Control
Left Side Code
Switches
Right Side
Code Switches
Battery Cover
5
598-1214-03
One remote control is able to independently operate
two receiver units. If more than two receiver units,
operating independently, are desired, additional
remote controls will need to be purchased.
1. Remove Tab from Battery Chamber. Remove
cover from back of transmitter. Gently pull tab
out of battery chamber (see Figure 1). Slide
cover onto transmitter.
REMOTE CONTROL
2. Remote Control Functions. The three buttons
on the left side of the remote will operate one
or more receiver units with matching code set-
tings. The three buttons on the right side of the
remote will operate a second set of one or more
receiver units (see Figure 2).
• ON: Turns on any receiver unit set to the same
code as this remote control.
• OFF: Turns off any receiver unit set to the same
code as this remote control.
Battery Chamber
(Type A23)
Battery Cover
Tab
ON DIP
1 2 3 4
ON DIP
1 2 3 4
Figure 1 - Rear View of Remote Control
6598-1214-03
4 5 43
1 2 32
Note: To independently operate a second receiver
unit using a single remote control, make sure the
second set of code switches (Right Side) and the
code switches on each receiver match (see Code
Settings section).
• Left Side - Set left side code switches.
• Right Side - Set right side code switches.
IMPORTANT: Wait 1 to 2 seconds after you press
a transmitter button before you press it again to
allow the transmission to be completed.
Note: If light does not turn on or intermittently
turns on and off when transmitter buttons are
pushed, see Troubleshooting Guide.
Figure 2 - Function Controls
Left Side DIM
Left Side ON
Left Side OFF
Right Side DIM
Right Side ON
Right Side OFF
• DIM:Activates the DIM feature for any receiver
unit set to the same code as this remote control.
Note: Pressing the DIM button steps through
five brightness levels.
7
598-1214-03
Figure 3 - Removing Visor Clip (Rear View)
Flat-Head
Screwdriver Optional
Visor Clip
Optional Car Visor Clip (Included)
The remote control includes an optional car visor
clip for added convenience that may be installed.
1. To attach car visor clip to remote control (if
desired) push it into slot on rear of remote unit
until it snaps into place (see Figure 3).
2. To remove car visor clip, insert a small, flat-
head screwdriver into slot on back of remote.
Gently push down on portion of visor clip inside
slot with screwdriver while pulling clip out of
remote from top (see Figure 3).
8598-1214-03
WIRELESS MOTION SENSOR
Features:
• No wiring required.
• Up to 70 feet sensing range, 180° Coverage.
• Adjustable sensitivity.
• Day/Night or Night only operation.
• Test mode.
• Uses 2 AA batteries.
• Wall or eave mount.
• Controls receivers up to 100 feet away.
Select Night or 24 Hour Mode
This sensor is able to detect motion day and night or
night only. To set the detection mode, remove rear
panel by sliding the panel down. Remove batteries
if necessary. Slide the DETECT switch to either the
DAY/NIGHT or NIGHT ONLY position. Replace
rear panel by reversing the above instructions.
Installing Batteries
Before mounting sensor, remove rear panel by
sliding the panel down. Install 2 AA batteries
according to polar-
ity markings inside
the battery compart-
ment (see Figure 4).
Replace rear panel
by reversing the
above instructions. Figure 4 - Battery
Compartment (Rear View)
DETECT
CODES
1234
DAY
NIGHT
NIGHT
ONLY
Detect
Control
Polarity
Mark
9
598-1214-03
Figure 5 - Installing Motion Sensor
Installing Motion Sensor
1. Install sensor mounting bracket where motion
detection is desired. Attach sensor mounting
bracket to a sturdy object (i.e. tree, post, house,
etc.) using two screws provided (see Figure 5).
Make sure unit has an unobstructed view. Note:
If mounting bracket to a curved surface, attach
mounting bracket vertically.
2. Install motion sensor to mounting bracket. Us-
ing a Philips-head screwdriver, loosen the clamp
screw on the mounting bracket. Insert swivel
ball mount on sensor into mounting bracket
socket (Note: You should hear a snap). Aim
sensor toward area where detection is desired.
Tighten clamp screw (see Figure 5).
IMPORTANT: The sensor must be mounted with
the bottom cover facing down in order to maintain
water tightness.
Mounting Bracket
Clamp Screw
Nut
Sensor
Mounting Screw
Swivel Ball Mount
Mounting Bracket
Socket
10 598-1214-03
Check Operation and Adjustment
Note: When first turned on or when switching
modes wait 1 1/2minutes.
The RANGE control and ON-TIME control are
located on the bottom of the sensor (see Figure 6).
Using your fingernails or a small, flat-head screw-
driver, gently pry the cover until it opens.
1. Check Operation. Set the ON-TIME control to
TEST mode. Walk in front of sensor unit. The
LED indicator light located on the bottom of
the sensor should flash when motion is detected
(see Figure 6).
2. Adjust Sensor. Turn the RANGE control to the
mid position and ON-TIME control to the TEST
position (see Figure 6). Walk through coverage
area noting where you are when the LED begins
to flash. Loosen the clamp screw and move the
sensor to change the coverage area (see Figure
7). Tighten clamp screw when finished. Do not
overtighten clamp screw.
Figure 6 - Motion Sensor Controls (Bottom View)
5 1 TEST
ON-TIME
(MINUTES)
RANGE
MAX MIN
ON-TIME
Control Sensitivity
Control
LED Indicator
Table des matières
Langues :
Autres manuels Ace Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
