Acclaim Lighting Terra Linear Manuel utilisateur
www.acclaimlighting.com
User guide
Terra Linear™
1
www.acclaimlighting.com
CONTENTS
INTRODUCTION ....................................... 2
Welcome 2
Safety, maintenance and cleaning 2
Supplied items 3
Required accessories 3
Optional accessories 4
INSTALLATION.......................................... 5
Mounting 5
Surface preparation and drainage 6
Mounting height 6
In-ground installation 7
Power 11
Interconnecting 12
Termination 12
Linking to an XTR Driver 13
Optional AJBOX1 conduit connections 14
Flexible power options 15
Run lengths - fixture maximum 16
Run lengths - overall maximum 16
Important cabling considerations 17
Control 18
DMX control considerations 19
Tips for achieving successful DMX control 20
Innovations to enable long runs 21
Optional wireless control 21
OPERATION ............................................22
Addressing fixtures 22
DMX cell addressing 23
Setting the cell mode (personality) 24
Testing emitter output 25
FURTHER INFORMATION............................26
Troubleshooting 26
Specifications 27
Dimensions 28
Limited product warranty 33
2www.acclaimlighting.com
INTRODUCTION
WELCOME
Welcome to the Terra Linear™ range from Acclaim Lighting. These tough, drive-over ready
fixtures designed for all-weather in-ground applications. Available in 1 foot and 4 foot
lengths, these aluminum-bodied IP68 fixtures are particularly suited to recessed façade
lighting applications. A wide range of emitter, beam angle and power options make it
straightforward to match each unit to the specific requirements of your installation.
Using unified power and DMX control links, Terra Linear fixtures can be rapidly daisy-chained
in long runs. All standard mains voltages are directly supported or, to achieve impressive
single runs up to 700 linear feet (213m), Terra Linear can be driven by Acclaim Lighting’s XTR
Driver.
Control is achieved using the industry standard DMX-512A format, with RDM for
configuration. DALI and 0-10V control inputs can also be used when an XTR Driver or
optional converters are employed.
SAFETY
•When fixtures are mounted off-ground, ensure they are securely fitted to an appropriate
mounting surface.
•Ensure that the power input is supplied from an environmentally protected location, is
correctly fused and has a valid protective earth that is tied to true earth.
WARNING - HIGH VOLTAGE
This device can use high voltages (up to 400VDC) which could
cause severe personal injury or death if misused:
• Always isolate power before connecting or disconnecting links.
•Installation to be carried out by certied electricians only.
•Use only approved cables and connectors.
•Check all connections are correctly made before energizing.
HIGH VOLTAGE
MAINTENANCE
CAUTION: Always isolate mains power before starting maintenance operations.
•Ensure that all mounting (and device) screws/bolts are fully tight and free of corrosion.
•Ensure there is no deformation to the housing, lenses or fixing points.
•Check that all power supply cables are free from physical damage or material fatigue.
•Use only genuine spare parts supplied by Acclaim Lighting.
CLEANING
•Use a moist, lint-free cloth along with warm water when cleaning each fixture.
•Never use alcohol or solvents.
SAFETY, MAINTENANCE AND CLEANING
4www.acclaimlighting.com
OPTIONAL ACCESSORIES
IP66 junction box
(incl. outlet cable gland)
[AJBOX1]
Link cables
1’ (30cm) [TLALC1]
5’ (1.5m) [TLALC5]
10’ (3m) [TLALC10]
XTR Driver adapter cable
(allows a Terra Linear link
cable to be connected to an
XTR Driver output)
[TLAXTRC1]
Terminator (end cap)
[TLAEC]
5
www.acclaimlighting.com
INSTALLATION
MOUNTING
For each Terra Linear fixture, an in-ground aluminum sleeve of the same length is required
(see page 3 for part codes and page 28 for dimensions). Sleeves feature a removable
2” rubber knockout at each end as well as an aluminum pour cover along the upper
surface, which fully protects the internal chamber while surface work is in progress.
IMPORTANT: To achieve a full 6000 lbs (2,721kg) drive-over rating, the long sides
of each sleeve must be fully supported on 8” (203mm) concrete. Otherwise the
xture must be reduced to a walk-over rating of 2000 lbs (907kg).
Soft ground
base
Finishing
Concrete
TO ACHIEVE A FULL 6000 LBS DRIVE-OVER RATING
SOFT GROUND BASE - 2000 LBS WALK-OVER RATING
Terra Linear placed into sleeve
1.5” Conduit
Finishing
Concrete
Aluminum
retainers
(up to 6)
6www.acclaimlighting.com
SURFACE PREPARATION AND DRAINAGE
Correct surface preparation is essential to ensure that the required walk- or drive-over rating
is achieved (see page 5), as well as sufficient drainage to prevent permanent flooding of
the chamber(s).
Each sleeve should be mounted into a level surface that is free draining, such as a permeable
stone/gravel mix. If the base is concrete then suitable drainage holes should be created.
The following minimum drainage rates should be met or exceeded:
Sleeve length Sleeve volume Minimum drainage rate
1ft 0.6 gallons 0.022 gallons per minute
(2.7 liters) (0.1 liters per minute)
4ft 2.4 gallons 0.09 gallons per minute
(10.9 liters) (0.4 liters per minute)
Where drainage rates are insufficient, further measures should be employed, such as a
French drain below the immediate mounting surface of each sleeve.
MOUNTING HEIGHT
IMPORTANT: For walk- and drive-over installations, the long sides of the sleeve
must be fully supported and the sleeve height must be arranged to ensure that its
top edge is exactly level with the nished surface:
Soft ground
Walk-over applications
Concrete
Full drive-over rating
Soil
Stone/
gravel
mix
Sleeve too high
Sleeve too low
Sleeve level with surface
7
www.acclaimlighting.com
IN-GROUND INSTALLATION
The following section provides a brief overview of the recommended steps required to
successfully install a Terra Linear fixture.
TO INSTALL A TERRA LINEAR FIXTURE
1 Prepare the mounting location(s) - see ”Mounting”on page 5.
2 Remove the pour cover from the sleeve
as well as one or both of the 2”rubber
knockout(s).
3 Lay the sleeve in place and use up
to six retainers (by others) suitable
to the mounting surface to prevent
movement. The retainers should
be aluminum to prevent galvanic
corrosion and 6”(150mm) in length
or longer.
Sleeve
2” knockout
Pour cover
3rd party
retainers
Six mounting slots can
accommodate retainers up to
3/16” (4mm) in diameter
8www.acclaimlighting.com
4 Attach a suitable 1.5”conduit
(by others) to the inlet hole
and lock it in place.
Repeat for the outlet hole, if
required.
1.5” conduit
Conduit
lock nut
•Where sleeves are abutted,
use suitable 1.5” conduit
couplers to secure the
joins.
Conduit coupler
(and lock nut)
Table des matières
Autres manuels Acclaim Lighting Équipement d'éclairage
Acclaim Lighting
Acclaim Lighting Ai Flex Interior Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Flood One EO Series Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Pixel Bar Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Flex Tube SC G2 Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Aqua Graze Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Flex Tube Pixel Manuel utilisateur
Acclaim Lighting
Acclaim Lighting ART-4 Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Dyna Accent Mini Manuel utilisateur
Acclaim Lighting
Acclaim Lighting aria Dyna Accent Manuel utilisateur
Acclaim Lighting
Acclaim Lighting AL-BAR-AC-DMX-1200-RGB Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Unity SNS2019 Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Flex Tube Mini Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Flex One Exterior Series Manuel utilisateur
Acclaim Lighting
Acclaim Lighting AL Dot Manuel utilisateur
Acclaim Lighting
Acclaim Lighting Linear XTR Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
