AbleNet Relax IR Learning Remote Manuel utilisateur

Charging

= Charging

= Full Charge

Quick Start Guide

Relax™ IR Learning Remote

Product Overview

Switch

Input

Learn

Button

Scan

Speed

Lock

Switch

On/Off

Switch

Micro USB

Charging Jack

Programmable

Function

Button LEDs

Programmable

Function

Buttons

Mounting Plate

Attachment

Screw Threads

Approximate Location of

IR Transceivers

Program

Unlike some universal remotes that use a code to program the whole remote at

one time, the Relax remote records the IR signal of your remote and programs one

function at a time. You specify which Programmable Function Button on the Relax

remote the IR signal is recorded to and can program one to eight separate functions

to the Relax remote. To program your Relax remote follow these instructions:

1. Turn the Relax remote ON

2. Hold the Learn button down approximately 5 seconds until appears on

the LED Display.

3. Select a Programmable Function Button that you would like to record to. Once

selected the Programmable Function Button LED will turn red.

4. Position IR remote as shown.

5. Activate desired function button on IR Remote. When the Relax remote

successfully records the IR signal, the Programmable Function Button

LED will turn orange.

6. To program additional Function Buttons on the Relax remote, repeate steps 3

through 5 above.

7. Once ﬁnished programming the Relax remote, press the Learn button and

will disappear from the LED Display.

Place remotes less

than 6-in/15-cm apart

LED

Display

Plug Micro USB

charger into

Charging Jack.

PN 98000042 (10/14 Rev. A - FN 70500204)

Use

Direct Select:

Press any of the Programmable Function buttons to activate the desired function.

Before Switch Scanning can be used, the Relax Remote must be programmed.

Switch scanning set up:

1. Turn the Relax Remote on by moving the On/Off Switch from the O to the I position.

2. Using the Scan Speed + or – button, set the desired number of seconds from one to 10 for the scan rate. The scan rate is the amount of time it

takes to move between Programmable Function buttons on the Relax Remote once a switch has been activated.

3. Once the scan rate has been set, plug a 3.5mm switch plug into the Switch Jack on the Relax Remote.

Using switch scanning:

1. To start the scan, activate the switch one time. On the Relax Remote, the scan moves from top to bottom. As the scan moves through the Relax

Remote, the LED on each Programmable Function button will turn on to indicate that it is the current option for the user to select.

2. To select a Programmable Function Button, the user will activate the switch one time.

It is possible for a user to activate the same Programmable Function button multiple times without having to go through the entire scan. The amount of

time the scan will stay on the same Programmable Function button is determined by the scan rate that has been set. For example, if the scan rate is

set to ﬁve-seconds, and the user selects a Programmable Function button for channel up, they have ﬁve-seconds to activate the switch again to select

that same channel up function. After ﬁve-seconds passes, the scan will re-start at the top of the Relax Remote.

The scan on the Relax Remote will move from top to bottom for three full cycles. If no switch activation occurs after the third cycle is complete, the

scanning will stop. You may then re-start the scanning by activating the switch one time.

Single function switch set up and use:

With the Relax Remote, a user can use a switch to activate a single function on the remote.

1. Turn the Relax Remote on by moving the On/Off Switch from the O to the I position.

2. Plug a 3.5mm switch plug into the Switch Jack on the Relax Remote.

3. Activate the switch one time. You will see the scan begin at the top of the Relax Remote; the Programmable Function button LED will turn orange

when the scan is on that function.

4. When the scan reaches the Programmable Function button you would like to control with the Switch, move the Lock Switch to the “locked”

position.

5. Each time the switch is now activated, the single selected function will be activated and the LED Display on the Relax Remote will now show

“LOC” each time the switch is activated.

Tricks, Tips, and Warranty

On some remotes, you may have to program a function more

than once.

LED Display

Relax is in Learning Mode

Relax is Charging

Relax is locked into a speciﬁc location for the

switch

Relax is Fully Charged

Function has been erased from Relax

Relax battery is low

Digits to show scanning time. Can be from 1.0 to

10.0 seconds in 0.5 second increments.

Erase all programmed functions:

To erase all of the programmed functions on the Relax Remote,

hold the Learn Button down for approximately 10-seconds. The

LED Display will ﬂash “dEL” off and on ﬁve times. If you press

a Programmable Function Button after it has been erased, the

LED will show “dEL.”

Size: 7.25 x 3 x 1 inch [184 x 76 x 25 mm]

Weight: 8 oz [225 grams]

Battery: Li-ion Rechargeable

Field of View: 110 degrees

Operating Temperature: 0-40°C, 32-105°F

Switch Input: 3.5mm (1/8”), mono jack

Warranty Information

AbleNet manufactured products include a two-year limited

warranty. This warranty is against defects in materials and

manufacturing for two-years from the date of purchase.

Warranty in full text, along with return/repair information is

available at www.ablenetinc.com.

For more information on AbleNet products and services,

contact:

AbleNet, Inc.

Minneapolis/St. Paul, MN

800-322-0956

www.ablenetinc.com

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Consult AbleNet Technical Support or your local Distributor for help.

Table des matières

Autres manuels AbleNet Télécommande