ABL AIP-2MBV Manuel utilisateur

HD IR Waterproof Fixed Network Camera （With Integrated

Bracket）Quick Start Guide

Version 3.3.3

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please

note: Do not connect two power supplying sources to the device at the same time; it may result

in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

Dome enclosure is the optical component, do not touch the enclosure when you are installing the

device or clean the enclosure when you are doing maintenance work. Please use professional optical

clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result

in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

12V to 24V Conversion Cable

(For AC 24V series product only)

iii

Table of Contents

1Framework...................................................................................................................................1

1.1 Multiple-function Combination Cable ........................................................................1

1.2 Framework and Dimension.........................................................................................2

1.3 Bidirectional Talk ..........................................................................................................3

1.3.1 Device-end to PC-end..........................................................................................3

1.3.2 PC-end to the Device-end....................................................................................3

1.4 Alarm Setup...................................................................................................................4

2Installation....................................................................................................................................6

2.1 Device Installation ........................................................................................................6

2.2 Micro SD Card Installation ..........................................................................................7

2.3 Lens Adjustment...........................................................................................................9

2.4 Bracket Adjustment......................................................................................................9

2.5 OSD Buttons ...............................................................................................................11

3Quick Configuration Tool.........................................................................................................13

3.1 Overview......................................................................................................................13

3.2 Operation.....................................................................................................................13

4Web Operation..........................................................................................................................15

4.1 Network Connection...................................................................................................15

4.2 Login and Main Interface...........................................................................................15

Appendix Toxic or Hazardous Materials or Elements ...............................................................18

1Framework

1.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See

Figure 1-1.

Figure 1-1 Multiple-function combination cable

Please refer to the following sheet for detailed information.

Port Name

Function

Connection

Note

DC 12V/AC

24V

Power input

port

Power port. Input DC 12V/AC 24V (Please

use the provided conversion cable)

Reset

Reset port

Hardware reset function. Press it for 3 to 5

seconds; system hardware can restore

default setup.

I/O

I/O port

Connect to I/O port.

LAN

Network port

Ethernet

port

Connect to standard Ethernet cable.

AUDIO IN

Audio input

port

RCA

Input audio signal. It can receive the analog

audio signal from the pickup.

AUDIO OUT

Audio output

port

RCA

Output audio signal to the devices such as

the sound box.

VIDEO OUT

Video output

port

BNC

Output analog video signal. It can connect to

the TV monitor to view the video.

Please refer to the follow sheet for detailed I/O port information.

Port Name

Name

Note

I/O Port

ALARM_COM

Alarm output public port.

ALARM_NO

Alarm output port. It is to output the alarm signal

to the alarm device.

NO: normal open alarm output port.

It works with the ALARM_COM port.

ALARM_IN1

Alarm input port 1. It is to receive the on-off signal

from the external alarm source.

ALARM_IN2

Alarm input port 2. It is to receive the on-off signal

from the external alarm source.

GND

Ground port

1.2 Framework and Dimension

Please note all frame and dimension illustrations provided in this chapter are for

reference only, and actual product may vary.

Please refer to Figure 1-2 or Figure 1-3 for dimension information according to the actual product.

The unit is mm. Please also see Figure 1-4.

Figure 1-2 Dimension illustration 1

Figure 1-3 Dimension illustration 2

Figure 1-4 Dimension illustration 3

1.3 Bidirectional Talk

1.3.1 Device-end to PC-end

Device Connection

Please connect the speaker or the MIC to the audio input port of the device. Then connect the

earphone to the audio output port of the PC.

You can see the button becomes orange after you enabled the audio talk function.

Click Audio button again to stop the bidirectional talk function.

Listening Operation

At the device end, speak via the speaker or the pickup, and then you can get the audio from the

earphone or sound box at the pc-end.

1.3.2 PC-end to the Device-end

Device Connection

Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone

to the audio output port of the device.

You can see the button becomes orange after you enabled the audio talk function.

Click Audio button again to stop the bidirectional talk function.

Please note the listening operation is null during the bidirectional talk process.

Listening Operation

At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the

earphone or sound box at the device-end.

1.4 Alarm Setup

The alarm interface is shown as in Figure 1-5. Please follow the steps listed below for local alarm

input and output connection.

1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.

2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public

port (No.1 pin). The alarm output port supports NO (normal open) alarm device only.

3) Open the Web, go to the Figure. Please set the alarm input 01 port for the first channel of the

I/O cable (No.3 pin). The alarm input 02 is for the 2nd channel of I/O cable (No.4 pin). Then you

can select the corresponding type (NO/NC.)

4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is

the No.2 pin of the I/O cable.

Figure 1-5 Alarm

Please refer to the following figure for alarm input information. See Figure 1-6.

Alarm input: When the input signal is idle or grounded, the device can collect the different

statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the

device collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 1-6 Alarm input

Please refer to the following figure for alarm output information. See Figure 1-7.

Port ALARM_COM and Port ALARM_NO composes an on-off button to provide the alarm output.

If the type is NO, this button is normal open. The button becomes on when there is an alarm

output.

If the type is NC, this button is normal off. The button becomes off when there is an alarm output.

Figure 1-7 Alarm output

2Installation

Please note all frame and dimension illustrations provided in this chapter are for

reference only, and actual product may vary.

2.1 Device Installation

Please refer to Figure 2-1 or Figure 2-2 for installation information according to the actual product.

Please follow the steps listed below to install the device.

Please draw the installation holes in the installation surface and then mark three

expansion bolts holes in the surface. Insert three bolts in the hole and secure firmly.

Please line up the installation holes of the bottom of the pendant mount bracket to the

installation holes in the surface. Then insert the three bolts to the holes of the bottom of

the bracket. Finally fasten the device on the installation surface.

Figure 2-1 Device installation 1

Table des matières

Autres manuels ABL Caméra de sécurité

ABL

ABL AIP-1MBF Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur