Abcon POSTSHIP Series Manuel utilisateur

ON/OFF UNIT HOLD ZERO

HOLD

The ultimate multi-purpose digital scale

Ideal for letters, parcels and large boxes

INSTRUCTION MANUAL

CONTENTS

03 Safety Precautions

-Warnings

-Cautions

-Battery Installation & Replacement

05 Parts Description

06 Functions

-Hold Function

-Measuring Unit Change/Conversion

-Programmable Function Settings

08 Weighing

-Weighing Procedures

09 Calibration

-Using Any Weight Calibration®

System

-What Is The The Any Weight

Calibration® System?

-How To Calibrate

11 Features

12 Speciﬁcations

13 Troubleshooting and Helpful Tips

14 Cleaning

SAFETY PRECAUTIONS

Please retain these instructions for future use.

All safety messages are identiﬁed by the words “WARNING” and “CAUTION”. These

words mean the following:

WARNING

Important information to alert you to a

situation that might cause serious injury and

damage to your property if instructions are not

followed.

CAUTION Important information that tells how to prevent

damage to the equipment.

When using the scale, the following safety precautions should always be followed:

WARNING

• Use only the correct AC adaptor with the scale. Other adaptors may cause permanent

electrical damage.

• DO NOT use AC adapter at the same time as batteries, use only one power source.

CAUTION

• This is not a toy, children should be supervised at all times if using this product.

• Always use on a stable level surface.

• Avoid placing the scale in direct sunlight, this may cause discoloration or malfunction.

• If the scale is not to be used for a long period of time, remove all batteries from the

battery compartment to avoid leakage, which may cause damage to this scale.

• Avoid overloading the scale, as this may cause permanent damage and void your

warranty – DO NOT EVER exceed the maximum capacity of the scale.

• Keep the scale away from water – this scale is not water resistant. Shock, injury and

electrical damage can occur if used in a wet location!

• DO NOT operate a mobile or cordless phone or any other electronic device with

strong magnetic ﬁeld (i.e. computer, radio, TV) within 3m of this device.

SAFETY PRECAUTIONS

BATTERY INSTALLATION AND REPLACEMENT

• Always take care to ﬁt your batteries correctly, observing the plus and minus markings.

• Always replace a whole set of batteries at one time. DO NOT mix old and new

batteries.

• Only use the same or equivalent recommended type of batteries, DO NOT mix type.

• Always store unused batteries in their packaging and away from metal objects that

may cause a short circuit.

• Remove dead batteries from the product and remove batteries if you will not be using

the product for an extended period.

• Always make sure battery compartments are secure.

• NEVER dispose of batteries in ﬁre - Risk of batteries exploding.

• NEVER attempt to recharge normal batteries.

• Rechargeable batteries should be removed from the appliance before being charged.

HOLD

PARTS DESCRIPTION

RIGHT SIDE

A AC adaptor Socket

FRONT

B ON/OFF KEY

Turns the scale power on/off

C UNIT KEY

Changes weighing units, e.g. kg or lb.

D HOLD KEY

The item’s weight reading will

remain on the display

E ZERO KEY

(for TARE 100% to full capacity)

Sets display to zero or subtracts

weight of a container

DISPLAY

F ZERO Indicator

G Weighing Unit

H Negative Value Indicator

I Hold Indicator

J Stable Indicator

TOP

K Platform:

Slots into top of scale base when

setting up scale for ﬁrst use

L Base of scale

BOTTOM

M Battery compartment cover

N Use 6 x AA 1.5V batteries

CB D E

FUNCTIONS

HOLD FUNCTION

Once the HOLD button is pressed, the indicator will remain on the display for 120

seconds after the item has been removed from the scale so the weight can easily be read.

1. Place the item on the scale platform.

2. Wait for the stable indicator to be displayed.

3. Press the [HOLD] button. The HOLD hold indication will turn-on.

4. Remove the item from the scale platform. The item’s weight will remain on the display

for 120 seconds. Convert this to other measuring units (example: lb to kg) by pressing

the [UNIT] button.

5. To quit HOLD function, press the [HOLD] button again.

MEASURING UNIT CHANGE / CONVERSION

BEFORE PLACING ITEM ON PLATFORM:

The measuring unit (i.e. g or oz) can be chosen before placing item onto weighing

platform by pressing [UNIT] button.

WHILST ITEM IS ON PLATFORM (CONVERSION):

If you did not choose the desired measuring unit before placing item onto platform, it is

still not too late to change (covert) it. Simply press the [UNIT] button with the item still on

the platform (or when in Hold mode) and the unit reading will be converted to your new

chosen unit [i.e. lb:oz to kg].

PROGRAMMABLE FUNCTION SETTINGS (Auto Off / Auto Backlight / Auto Hold)

ENTERING CHANGE FUNCTION MODE:

In order to change the current function settings, it is required to enter the Change

Function mode by ﬁrst ensuring the scale is switched OFF. Then press and hold the

[ZERO] button whilst pressing the [ON/OFF] button. Now the display will show:

A_ON or A_OFF

1. AUTO SHUT OFF MODE:

Press the ZERO button, the display will show A_ON or A_OFF. A_ON means the

auto shut off function is active. Press [ZERO] again, the display will show A_OFF,

this means the auto shut off function is inactive.

FUNCTIONS

2. AUTO BACKLIGHT MODE:

Press [UNIT] button until the display shows L_ON or L_OFF, press [ZERO],

selection to display L_ON, this means backlight function active, press [ZERO]

again, the display will show L_OFF, this means backlight function inactive.

3. SELECTION OF AUTO HOLD MODE:

Press [UNIT] button until the display shows H_ON or H_OFF, press [ZERO],

selection to display H_ON, this means AUTO-HOLD function active, press

[ZERO] again, the display will show H_OFF, this means AUTO-HOLD function

inactive.

4. RETURN TO WEIGHING MODE:

Press [ON/OFF] to turn the power off, press [ON/OFF] again to turn on the

power and the scale will return to weighing mode.

WEIGHING

Whenever possible, please allow the scale to warm up for several seconds after ﬁrst

turning the power on so that the scale will function properly and accurately.

ERROR MESSAGES:

EEEE or Err-O = Overload

, Lob or LoBatt = Low Battery

WEIGHING PROCEDURES

1. Press [ON/OFF] to turn on the scale. The display will count down from “999999” to

“111111” and then “0” appear on the display.

2. Select the weighing unit by pressing [UNIT] button.

3. The selected weighing unit will be displayed on the cursor next to the weight value.

4. Start weighing. Make sure the display is “0”, if not press the [ZERO] button to zero the

scale.

5. If you are using a container or tray, place the empty container on the scale, wait for the

stability indicator to be displayed, press [ZERO], the display will read “0” with the tray

or container on top.

CALIBRATION

USING ANY WEIGHT CALIBRATION® SYSTEM

During manufacture the scale is already accurately calibrated. However when the scale is

ﬁrst set up for use it may be desired to calibrate it, or after time and use when mechanical

deviations can occur making the scale less accurate. If the scale has been moved to a

different altitude or gravitation the scale can lose accuracy as the weight of a mass in one

location could be different to that in another location. It is also recommended to calibrate

in these circumstances.

What is the The Any Weight Calibration® System?

Normally when a user wishes to calibrate their scale, the manufacturer either requests the

unit be sent to its head ofﬁce service agent or ask that you purchase special accurate and

expensive weights.

The Any Weight Calibration® System allows you to calibrate without needing to use any

special weights. Instead you can use any object for which you know the weight for easy

and quick calibration. This could be, for example, items weighed at the deli or meat

counter in the supermarket, bags of pre-packed sugar, ﬂour or even packs of cola cans

or coins that you have had pre-weighed on Legal for Trade scales in the supermarket or

market. The weight can be in kg, g, lb or oz and do not have to be whole units, i.e. could

be 3.1kg, 5050g, 12.056lb or 7.8oz.

HOW TO CALIBRATE

It is recommended, but not essential, to use a total weight that is at least 50% of the

total capacity. So, for example, if your scale has a capacity of 16kg, then the ideal weight

to use would be 8-13kg. You could combine the known weight of several items. Never

exceed the total capacity of the scale. Lower calibration weights are OK (i.e. 5kg) if the

scale is normally only used with items that weigh less than 50% scale capacity.

1. Turn on the power by pressing [ON/OFF] and leave switched on for at least 1 minute

before proceeding to step 2 below.

2. Turn off power by pressing [ON/OFF]

• Press [UNIT] and [ON/OFF] at the same time, now the display will show “CALu=”

• Press [UNIT] to select the type of calibration unit to be used, i.e. kg, g, lb or oz.

• Press [ZERO] to enter the Weight Selection Mode. In this mode you are now able to

enter the exact weight of the item you are using to calibrate the scale.

Press [HOLD] = increases the value of the ﬂashing number

Press [UNIT] = moves to next number on the right

CALIBRATION

3 Press [ZERO], the display will now say “CAL” and then a 5 digit number which is a

special internal reference number. The last number(s) on the right will change up or

down slowly. When these numbers are hardly changing and/or the stable indicator is

showing press [UNIT]. The display will now ﬂash “- - - - -” for a second and then ﬂash

with the weight you entered.

• Place the item(s) to be used for calibration on the platform, wait for a moment and

then press [UNIT]. Another 5 digit number will appear on the display which you DO

NOT need to worry about.

• Press [ON/OFF] to turn scale off to complete and save the calibration.

If a mistake has been made, pressing [ON/OFF] before the end of step 3, will turn the

scale off and calibration will not have taken place.

To test the calibration was successful, turn on the scale by pressing [ON/OFF], once the

scale has ﬁnished self testing and the display shows 0, put item(s) used for calibration on

the platform and check the scale is weighing correctly. If not, repeat steps 2 & 3 again.

Table des matières

Autres manuels Abcon Échelle

Abcon

Abcon ProShip Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur