ABB Relion 615 series Manuel utilisateur
Relion® 615 series
Transformer Protection and Control
RET615
DNP3 Point List Manual
Document ID: 1MRS756881
Issued: 2010-06-11
Revision: B
Product version: 3.0
© Copyright 2010 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license
and may be used, copied, or disclosed only in accordance with the terms of such
license.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
ABB Oy
Distribution Automation
P.O. Box 699
FI-65101 Vaasa, Finland
Telephone: +358 10 2211
Facsimile: +358 10 22 41094
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure and/
or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby
requested to ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standards EN 50263 and EN 60255-26 for the EMC
directive, and with the product standards EN 60255-1 and EN 60255-27 for the low
voltage directive. The IED is designed in accordance with the international
standards of the IEC 60255 series.
Table of contents
Section 1 Introduction.......................................................................3
This manual........................................................................................3
Intended audience..............................................................................3
Product documentation.......................................................................4
Product documentation set............................................................4
Document revision history.............................................................5
Related documentation..................................................................6
Symbols and conventions...................................................................6
Safety indication symbols..............................................................6
Manual conventions.......................................................................6
Functions, codes and symbols......................................................7
Section 2 DNP3 data mappings.....................................................11
Overview...........................................................................................11
Point list for RET615 Ver.3.0 TE01-08.............................................12
Section 3 DNP3 protocol implementation.......................................23
DNP3 device profile..........................................................................23
DNP3 implementation table..............................................................25
Section 4 Glossary.........................................................................29
Table of contents
RET615 1
Point List Manual
2
Section 1 Introduction
1.1 This manual
The point list manual describes the outlook and properties of the data points
specific to the IED. The manual should be used in conjunction with the
corresponding communication protocol manual.
1.2 Intended audience
This manual addresses the communication system engineer or system integrator
responsible for pre-engineering and engineering for communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1MRS756881 B Section 1
Introduction
RET615 3
Point List Manual
1.3 Product documentation
1.3.1 Product documentation set
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manual
Operation manual
Installation manual
Service manual
Engineering manual
Commissioning manual
Communication protocol
manual
Technical manual
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manualApplication manual
Operation manualOperation manual
Installation manualInstallation manual
Service manualService manual
Engineering manualEngineering manual
Commissioning manualCommissioning manual
Communication protocol
manual
Communication protocol
manual
Technical manualTechnical manual
en07000220.vsd
IEC07000220 V1 EN
Figure 1: The intended use of manuals in different lifecycles
The engineering manual contains instructions on how to engineer the IEDs using
the different tools in PCM600. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also
recommends a sequence for engineering of protection and control functions, LHMI
functions as well as communication engineering for IEC 61850 and other
supported protocols.
The installation manual contains instructions on how to install the IED. The
manual provides procedures for mechanical and electrical installation. The chapters
are organized in chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED.
The manual can also be used by system engineers and maintenance personnel for
assistance during the testing phase. The manual provides procedures for checking
of external circuitry and energizing the IED, parameter setting and configuration as
Section 1 1MRS756881 B
Introduction
4RET615
Point List Manual
Autres manuels pour Relion 615 series
41
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels ABB Relais
ABB
ABB CO Manuel
ABB
ABB RED615 ANSI Manuel utilisateur
ABB
ABB BL-1 Manuel utilisateur
ABB
ABB TRB Series Manuel
ABB
ABB REJ 521 Manuel utilisateur
ABB
ABB RED670 Relion 670 series Guide de démarrage rapide
ABB
ABB SGR-51 Manuel utilisateur
ABB
ABB CVE Manuel
ABB
ABB REF 610 Manuel utilisateur
ABB
ABB CIRCUIT SHIELD 87T Manuel utilisateur
ABB
ABB SPAM 150 C Manuel de la liste des pièces
ABB
ABB CIRCUIT SHIELD 437W Series Manuel utilisateur
ABB
ABB REF 610 Manuel du produit
ABB
ABB E 320 DU Manuel utilisateur
ABB
ABB REL-300 Manuel utilisateur
ABB
ABB RED615 ANSI Manuel utilisateur
ABB
ABB CM Series Manuel utilisateur
ABB
ABB REX 521 Manuel d'utilisation et d'entretien
ABB
ABB SPAU 331 C Manuel de la liste des pièces
ABB
ABB RELION Series Manuel d'installation et d'exploitation
