ABB Relion 620 Series Manuel utilisateur

Relion® 620 series

Advanced Recloser Protection and Control

RER620

IEC 60870-5-101/104 Point List Manual

Document ID: 1MAC302441-MB

Issued: 11/23/2010

Revision: A

Product version: 1.0

This document and parts thereof must not be reproduced or copied without written

permission from ABB, and the contents thereof must not be imparted to a third party, nor

used for any unauthorized purpose.

The software or hardware described in this document is furnished under a license and may

be used, copied, or disclosed only in accordance with the terms of such license.

Trademarks

ABB and Relion are registered trademarks of ABB Group. All other brand or product

names mentioned in this document may be trademarks or registered trademarks of their

respective holders.

Warranty

Please inquire about the terms of warranty from your nearest ABB representative.

ABB Inc.

Distribution Automation

4300 Coral Ridge Drive

Coral Springs, FL 33065, USA

Toll-free: 1 (800) 523-2620

Phone: +1 954-752-6700

Fax: +1 954 345-5329

http://www.abb.com/substationautomation

Disclaimer

The data, examples and diagrams in this manual are included solely for the concept or

product description and are not to be deemed as a statement of guaranteed properties. All

persons responsible for applying the equipment addressed in this manual must satisfy

themselves that each intended application is suitable and acceptable, including that any

applicable safety or other operational requirements are complied with. In particular, any

risks in applications where a system failure and/or product failure would create a risk for

harm to property or persons (including but not limited to personal injuries or death) shall

be the sole responsibility of the person or entity applying the equipment, and those so

responsible are hereby requested to ensure that all measures are taken to exclude or

mitigate such risks.

This document has been carefully checked by ABB but deviations cannot be completely

ruled out. In case any errors are detected, the reader is kindly requested to notify the

manufacturer. Other than under explicit contractual commitments, in no event shall ABB

be responsible or liable for any loss or damage resulting from the use of this manual or the

application of the equipment.

Conformity

This product complies with the directive of the Council of the European Communities on

the approximation of the laws of the Member States relating to electromagnetic

compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use

within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is

the result of tests conducted by ABB in accordance with the product standards EN 50263

and EN 60255-26 for the directive, and with the product standards EN 60255-6 and EN

60255-27 for the directive. The IED is designed in accordance with the international

standards of the IEC 60255 series and ANSI C37.90. The DNP protocol implementation

in the IED conforms to "DNP3 Intelligent Electronic Device (IED) Certification Procedure

Subset Level 2", available at www.dnp.org.

1MAC302441-MB A Table of contents

RER620 1

Point List Manual

Table of contents

Section 1 Introduction........................................................................... 3

This manual.............................................................................................. 3

Intended audience.................................................................................... 3

Product documentation ............................................................................ 4

Product documentation set ................................................................. 4

Document revision history................................................................... 5

Related documentation ....................................................................... 5

Symbols and conventions ........................................................................ 5

Safety indication symbols.................................................................... 5

Manual conventions ............................................................................ 6

Functions, codes and symbols............................................................ 7

Section 2 IEC 60870-5-101/104 data mappings ................................ 11

Overview ................................................................................................ 11

Point list for RER620 Ver. 1.0 ................................................................ 12

Section 3 IEC 60870-5-101/104 protocol implementation.................. 39

Section 4 Glossary ............................................................................. 51

Table of contents 1MAC302441-MB A

2 RER620

Point List Manual

1MAC302441-MB A Section 1

Introduction

RER620 3

Point List Manual

Section 1 Introduction

1.1 This manual

The point list manual describes the outlook and properties of the data points specific to the

IED. The manual should be used in conjunction with the corresponding communication

protocol manual.

1.2 Intended audience

This manual addresses the communication system engineer or system integrator

responsible for pre-engineering and engineering for communication setup in a substation

from an IED perspective.

The system engineer or system integrator must have a basic knowledge of communication

in protection and control systems and thorough knowledge of the specific communication

protocol.

Section 1 1MAC302441-MB A

Introduction

4 RER620

Point List Manual

1.3 Product documentation

1.3.1 Product documentation set

Figure 1: The intended use of manuals in different lifecycles

The engineering manual contains instructions on how to engineer the IED using the

different tools in PCM600. The manual provides instructions on how to set up a PCM600

project and insert IEDs in the project structure. The manual also recommends a sequence

for engineering of protection and control functions, LHMI functions, and communication

engineering for IEC 61850 and DNP3.

The installation manual contains instructions on how to install the IED. The manual

provides procedures for mechanical and electrical installation. The chapters are organized

in chronological order in which the IED should be installed.

The operation manual contains instructions on how to operate the IED once it has been

commissioned. The manual provides instructions for monitoring, controlling and setting

the IED. The manual also describes how to identify disturbances and how to view

calculated and measured power grid data to determine the cause of a fault.

The application manual contains application descriptions and setting guidelines sorted per

function. The manual can be used to find out when and for what purpose a typical

protection function can be used. The manual can also be used when calculating settings.

The technical manual contains application and functionality descriptions and lists function

blocks, logic diagrams, input and output signals, setting parameters and technical data

Planning & purchase

Engineering

Installing

Commissioning

Operation

Maintenance

Decommissioning

Deinstalling & Disposal

Application manual

Operation manual

Installation manual

Engineering manual

Communication Protocol

manual

Technical manual

Protocol Points List

manual

Autres manuels pour Relion 620 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ABB Contrôleurs

ABB

ABB AC500-S Instructions d'installation et d'utilisation

ABB

ABB AC500-eCo Series Manuel de référence

ABB

ABB PSTX Series Mode d’emploi

ABB

ABB C1900RC Manuel utilisateur

ABB

ABB LME620-AI Manuel utilisateur

ABB

ABB Relion 670 series Manuel d'installation et d'exploitation

ABB

ABB ACS150 series Manuel utilisateur

ABB

ABB ACS150 series Manuel utilisateur

ABB

ABB PST Series Mode d’emploi

ABB

ABB ControlMaster CM30 Manuel utilisateur

ABB

ABB COM600S IEC Manuel utilisateur

ABB

ABB AC 800F Manuel d'installation et d'exploitation

ABB

ABB UMC100.3 Manuel utilisateur

ABB

ABB PLUTO Safety-PLC Guide de l'utilisateur

ABB

ABB 300-line Manuel utilisateur

ABB

ABB IRC5 Compact Manuel utilisateur

ABB

ABB AC 900F Mode d’emploi

ABB

ABB STD-MTS Manuel utilisateur

ABB

ABB MS132 Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

ABB

ABB Advant Controller 450 Manuel utilisateur

ABB

ABB i-bus EIB/KNX AA/S 4.1 Manuel utilisateur

ABB

ABB PM564-R-AC Manuel utilisateur

ABB

ABB i-bus SA/S 12.16.6.1 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur