AAMP Global PAC APSUB-CH21 Manuel utilisateur
Rev: V1
Date: 091120 Page 1
Pacific Accessory Corporation
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
Advanced Subwoofer Amplier Interface for
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH21
The APSUB-CH21 provides a 2-channel non-fading pre-amp output for use with an aftermarket amplier and
subwoofer. Using the full range, xed level head unit output, in conjunction with CAN messages, the APSUB-CH21
delivers a low pass variable 5v RMS pre-amp output with bass equalization and level control capabilities. The signal
has a 350Hz / 24dB Linkwitz-Riley low pass lter applied. A data controlled remote amplier turn on wire is also
provided by the APSUB-CH21.
Introduction and Features
Important Notes
1. This interface is only compatible in vehicles equipped with a data-bus controlled amplied sound system. To verify
compatibility, look for an Alpine, Beats, Innity, or Harmon Kardon badge on the door speakers, center speaker, or factory
subwoofer grill. If none of these brands are shown; check for the presence of a center speaker or subwoofer.
2. The factory amplier must remain connected, and in the vehicle after the APSUB-CH21 has been installed.
3. The remote output is rated at 2A of current. If more current is needed; an external relay must be used.
4. The subwoofer outputs are non-fading. The output level of the subwoofer channel can be controlled using the supplied
level control knob. If the level control knob is not connected the output level will default to 100%.
5. The minimum volume level is set to a default. If you are happy with this level in your particular application then additional
adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
6. The level control knob must be connected in order to manually adjust the minimum volume setting.
7. No adjustments can be made manually using the programming button or the factory SWC when the module is connected
to a PC.
Wiring Connection Chart
To Aftermarket
Amplifier
Subwoofer Outputs
Remote Turn On Output
2A Max Output
AP4-CH21-HAR
To Radio To Vehicle
Harness
Non-Fading
Level Control
Knob
The aftermarket amplier must have a very solid ground and the amplier power/ground connections
should be made before connecting the RCA's or Remote Turn On to the APSUB-CH21
Rev: V1
Date: 091120 Page 2
Pacific Accessory Corporation
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
Advanced Subwoofer Amplier Interface for
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH21
Setup and Conguration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilloscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the minimum volume, do so using one of the methods outlined below. If you are happy with the
default level, no adjustment is necessary.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO app, please proceed to the AmpPRO App section.
PLEASE NOTE: Level control knob must be connected to module for either of the following methods.
Installation
1. Remove factory radio.
2. Disconnect the gray 22-pin factory harness connector from radio.
3. Connect APSUB harness to vehicle harness.
4. Connect APSUB harness to factory radio.
5. Set any feature DIP switches that apply to your install.
- Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 o (up) to keep the
RCA output voltage at 5v.
- DIP switches 1, 3, and 4 are not used.
6. Connect the APSUB harness to the module.
7. Connect the level control knob to the module and install in an accessible location.
8. After the aftermarket amplier power/ground connections are made, connect the signal cables and remote input from the
aftermarket amplier to the APSUB.
9. Reconnect any additional harnesses removed from the radio and reinstall the radio.
DIP
1 2 3 4
ON
No Function 5v / 4v Preout No Function No Function
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
Subwoofer Output
LED 2
Rev: V1
Date: 091120 Page 3
Pacific Accessory Corporation
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
Advanced Subwoofer Amplier Interface for
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH21
PLEASE NOTE: These settings can be adjusted with the module installed in the vehicle or on the bench. However, it is
recommended to make the adjustments with the module installed, and the factory radio on so that the changes can be
heard.
Minimum Volume Level - This allows you to set the minimum volume level of the factory radio (factory radio volume level 1).
EQ Enabled - This allows you to enable / disable the bass band factory EQ.
Bass Freq / Q Factor - This allows you to set the center frequency that will be adjusted when setting the bass band on the
factory EQ, as well as the Q Factor for each frequency. The Q Factor determines how many of the adjacent frequencies will
be aected when adjusting the selected frequency. The lower the Q Factor, the more frequencies will be aected. Note: This
setting only aects the output of the APSUB and does not change the way that the factory EQ adjusts the factory speakers.
Setup and Conguration (cont)
Setting the minimum volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface once.
5. LED 1 will turn amber.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Setting the minimum volume using the factory SWC
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press and hold the track up button on the factory SWC (Back left of steering wheel) for approximately ten seconds.
PLEASE NOTE: The radio will respond to the SWC commands during this process, this is normal and has no eect on the
APSUB operation.
5. LED 1 will turn amber.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
AmpPRO PC App
Use of the AmpPRO PC App
allows you to do the following:
• Congure User Interface Options such as:
• Minimum Volume Level
• Enable / Disable Factory EQ
• Set Bass Center Frequencies and Q Factor
• Update Product Firmware
• Read Firmware / Hardware Versions
• You can download the AmpPRO app at :
https://pac-audio.com/app-downloads/
Rev: V1
Date: 091120 Page 4
Pacific Accessory Corporation
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
Advanced Subwoofer Amplier Interface for
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH21
Restoring Factory Settings
You can restore the interface to factory default settings by pressing and holding the programming button on the side of the module
for 10 seconds until the status LEDs start blinking red. Once the LEDs start blinking red, release the button.
This reset will restore the following settings to their factory defaults:
• Minimum Volume Level
• Enable / Disable Factory EQ
• Factory EQ Frequency
• Factory EQ Q Factor
Firmware Updates
The AmpPRO app will also allow you to update the interface with new rmware as it becomes available. Please visit
www.pac-audio.com or contact our tech support department to see if there is a rmware update for your interface.
Connect the interface to your PC and select "Firmware", then “Update Firmware”. Now select “Select File”. Finally, browse to the
place where you saved the le and select it. This will begin the updating process. Once nished, disconnect the interface from
the PC and resume normal operation.
AmpPRO PC App (cont)
60HZ
80HZ
100HZ
120HZ
0.50
1.00
1.50
2.00
Bass
Frequency
Bass
Q Factor
AVAILABLE FREQUENCIES AND Q FACTORS
F1: 60Hz Center Frequency | 0.50 Q Factor F2: 100Hz Center Frequency | 2.00 Q Factor
20 63 125 250 500
1k 2k 4k 8k 16k 20k
dB
+15
+12
+9
+6
+3
0
-3
-6
-9
-12
F1 F2
Rev: V1
Date: 091120 Page 5
Pacific Accessory Corporation
© 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-Audio.com
Advanced Subwoofer Amplier Interface for
for Select Chrysler / Dodge / Jeep Vehicles
APSUB-CH21
Troubleshooting
1. Low volume setting on radio is too loud - Set minimum volume using process outlined in Setup and Conguration, or using
the AmpPRO application.
2. If for any reason the APSUB module becomes unresponsive, or will not power up with the key on, you can always reset the
interface by turning the key to the ignition position, then pressing and holding the Volume Down button on the factory SWC for
12 seconds until a tone is heard or by pressing and holding the reset button on the side of the APSUB module for 10 seconds
(until the LEDs alternate ashing red).
LED Legend
LED 1
Action/Color During Normal Operation
Solid Red Module Active
Solid Amber Minimum Volume Adjustment Mode
Rapid Blink Any Color DSP Activity
LED 2 Blinking Amber USB Connection Detected
Both LEDs Alternate Blinking Red Performing Memory Reset
Technical Support
Email: support@PAC-audio.com
Phone: 727-592-5991
Chat: PAC-Audio.com
Table des matières
Autres manuels AAMP Global Récepteur de voiture
