7inova 7W211 Manuel utilisateur
Wireless-N WiFi Repeater 300Mbps
Model: 7W211
QUICK
INSTALLATION
GUIDE
LED indicators’ Status Description
WPS Button
Ethernet
Reset Button
WLAN LED
WPS LED
Ethernet LED
Power LED
Indicator Name
Power Status Indicator
Wireless Status Indicator
WPS Status Indicator
Ethernet Status Indicator
Green On
Green slow blink
Green fast blink
Off
Constant On (Off after 5mins)
Green fast blink
Green fast blink
Green On
Get Powered
Wireless Function Launched
WPS Function Launched
Not use or have completed the connection
WPS pairs successfully
Data Transmission via Ethernet
Ethernet Connected
Data Transmission via wireless
Status Description
REPEATER
CLIENT
WPS One Button SetupFunctions Introduction
Before you start to use this device, please check if there’s anything
missing in the package, and contact your dealer of purchase to claim for
missing items:
PACKAGE CONTENTS:
Cautions:
1. Disconnect the device in thunderstorms in case of lightning damage.
2. Keep far from heat source and ensure ventilation.
3. Keep waterproof in the storage, transportation and operating environment.
QIG
Quick
Installation
Guide
Ethernet CableWiFi Repeater
A P Wireless Access Point
(AP: convert wired network to wireless network)
This Device can be used as a wireless AP, make your wired
network WiFi ready, your wireless devices can go internet
wirelessly via our repeater.
Client
(Client: convert wireless network to wired network)
Wired network devices (such as game console/computer), use
network cable connect the device through the CLIENT mode,
connect 2.4GHz wireless signal for Internet access.
Wireless Repeater
(Repeater: extend your existing wireless signal)
This Device connects to existing wireless network, and extends
wireless cover range.
Tips: Your root-wireless device can be scanned by this device,
and its signal strength should be no less than “ ”
Plug this device into socket, Power light should be constant on. WiFi LED always blinks, means the device starts to work.
1
Press WPS button of root-wireless device for 2seconds,
launch WPS function. (Please refer to your rooted wireless
device’s user manual for its WPS button usage)
The device’s WPS LED should be constant on, then means WPS connect successfully. (This WPS LED will turn off after 5 minutes)
2
4
In 2 minutes, press the WPS button of this device for 2seconds,
launch its WPS function. When WPS LED blinks, means
WPS is connecting.
3
ATTENTION: Above is only workable provided both of root-wireless device and this device have normally working WPS button. If
has no WPS button, please refer to “WiFi Repeater Web browser setup wizard”.
WPS
ADSL Router
Internet
Wireless Device
ADSL Router
Internet
Wireless Device
ADSL Router
Internet
Wired Device
Connect to a Network
Do you want to set up your network?
This is a new router that has not been set up. Click OK to start
setup.
Connect to the network without setting it up.
CancelO K
WiFi Repeater Web browser initial setup
Please check following
if need to change
working mode
1. Click “Start→Control Panel→Network and Internet→Network and SharingCenter→Change adapter settings→Wi-Fi(right click)→Properties”, Double click “Internet Protocol Version 4(TCP/IPv4)”.
2. To set up the computer IP 192.168.2.x (x arbitrary integer between 2~252), subnet mask of 255.255.255.0, Click “OK”. Back to the last interface and click “OK”. Then enter http://192.168.2.1
to configure.
Setup your computer’s IP after you finish configuration
1. Click “Start→Control Panel→Network and Internet→Network and Sharing Center→Change adapter settings→Wi-Fi(right click)→Properties”, Double click “Internet Protocol Version 4(TCP/IPv4)”
2. Select “Obtain an IP address automatically” and “Obtain DSN server address automatically”. Click “OK”. Back to the last interface and click “OK”. Then reconnect to repeater.
(If fails to connect network, Click “Start→Control Panel→Network and Internet→Network and SharingCenter→Change adapter settings→Wi-Fi(right click)→Properties→Diagnosis&Repair”;
Or please disconnect, and re-connect after 5 seconds.)
1
45
2 3
ATTENTION: Default SSID of this device is “current wireless network’s SSID+_2EX”, you can make clear whether your network is connected through this device;
6
Not connected
Connections are available
Wi-Fi
7inova-535060
7inova-535050
Connect automatically
7inova-521635
Open Network and Sharing Center
Information sent over this network might
be visible to others.
Connect
Setup your computer’s IP before connecting WiFi repeater
1) Restore Factory Setting: Plug the device into socket, press RESET button around 3-5seconds.
2) Default username: admin, Default password: admin (You can check on the label of device’s backside).
3) If get trouble in configure, fail to connect network, pls restore factory settings, then re-configure as per above steps.
Please use your PC, tablet or smart phone's wireless functions to search
for the device's SSID and connect.
Log in with Username and Password, both default are “admin”. Choose “Repeater”, click ”Apply”and then click “Search”. Select your wanted wireless network in the search list, enter the wireless network’s
passward, click “Apply”to finish setup. This device’s wireless password is same as
your root-wireless device’s wireless password.
Please click “ Connect to the network without setting it up”, wait
to connect. After connect successfully, enter “http://192.168.2.1” in web browser.
http://192.168.2.1Webstie
Appendix: Troubleshooting
Ce manuel convient aux modèles suivants
1
Autres manuels 7inova Répétiteur
