3M VB2/HC111-S Guide rapide
VB2/HC111-S and VB2/WCF110-L
Water Filtration Systems
Installation and Instruction Manual
INSTR4931 0909
2
3M™ Water Filtration Systems
Installation and Operating Instructions
Specifications
Inlet Size: 1/4” John Guest®Fitting
Outlet Size: 1/4” John Guest Fitting
Temperature Range: 40-100°F (4.4-38°C)
Pressure Range: 25-120 psi (172-827 kPa)
Dimensions - 2 3/4" W x 2 3/8" D x 12 1/2" H
(7.0 cm x 6.0 cm x 31.75 cm)
Parts Included
Filter Cartridge, System Head/Bracket Assembly
Installation Precautions
Warning: Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection
before or after the system. Systems certified for cyst
reduction may be used on disinfected waters that may
contain filterable cysts.
Caution: System must be protected from freezing.
Drain filter when room temperature drops below
40°F (4.4°C).
Caution: Do not install on hot water line. Maximum
temperature is 100°F (38°C).
• Donotusetorchorotherhightemperature
sources near filter or plastic cartridge.
• Donotinstallnearelectricwiresorwaterpipes
that will be in the path of the drill when selecting
the position to mount bracket.
• Donotinstallindirectsunlight.
• Allowminimumof2”(5cm)clearspaceunder
filter to facilitate cartridge change.
• Mountfilterinsuchapositionastopreventitfrom
being struck by other items.
• Installationmustcomplywithexistingstateor
local plumbing codes.
12.5”
(31.75 cm)
2 3/4”
(6.9 cm)
2 1/4”
(5.7 cm)
14.8”
(37.7 cm)
Cartridge Removed
Cartridge Installed
Figure 1
System Installation
1. Mount System
Determine mounting location
Warning: Before drilling mounting holes, locate any hidden electrical wires or plumbing behind the
mounting surface. Note adjacent equipment which may interfere with system fastening screws.
A. Fasten mounting bracket to mounting surface (screws not included).
Note: 2” (5 cm) free space underneath system required to change filter.
B. Removethecapfromcartridge.Inspectthecartridgeforanydamage.
C. Makesuretheo-ringsarepresentandpositionedcorrectlyingrooves.Moistentheo-ringswithfood
grade lubricant.
D. Connect the replacement cartridge to head/bracket assembly. Align tabs with head/bracket assembly
and push up until cartridge stops, then rotate 1/4 turn to the right to secure.
2. Cold Water Supply
Warning:Makesurecoldwatersupplyvalveisturnedoffpriortoinstallation.
The filter system's inlet connection is equipped with user-friends "quick-connect" push-in fittings, compatible
with 1/4" plastic or copper tubing. Figure 2.B shows how to use the quick connect fittings.
Note: A proper length of 1/4” copper or plastic tubing is required for installation (not included).
Installation must comply with existing state and local plumbing codes.
Note: Additional fittings may be required.
Note:Arrangetubingsothattherearenosharpbends.Leavesome“play”inthetubingforeaseof
servicing,thencuttubingtothedesiredlength.Shortertubinglengthsensurebetterflowrates.
3. Connect System
A. Your filter system connects directly to the equipment
via1/4”plastic or copper tubing. The filter system’s
inlet and outlet connections are equipped with user-
friendly“quickconnect”push-infittings.Referto
Figure 2.B.
4. Test System
A. Opencoldwatersupplyvalve.
B. The system will pressurize. Check for leaks. If any
leaks are present, refer to troubleshooting section.
5. Flush Filter
A. Make sure cold water supply is turned on.
B. Run water through the filter for 1 gallon (approximately
2minutes)toremoveanytrappedairandcarbonfines
or until water runs clear. Any air left in the system may
temporarily cause the water to be cloudy.
C. Yoursystemisnowreadyforservice.
Inlet
Outlet to
Equipment
3
Figure 2.A
4
Troubleshooting Guide
Water leaks at quick connect fittings
Pushtubinginasfarasitwillgo.Ifleakingcontinues,shutoffcoldwatersupplyandremovewaterlineby
pushing in on the connector collar while pulling the tubing away. Inspect tubing for cracks. If tubing is
cracked, simply cut that portion away and re-insert tubing into quick connect fitting.
Water does not flow from the filter
Checktoseeiftheoriginalwatersupplyvalveisopen,allowingwatertoflowtothefilter.Ifwaterstilldoes
not flow, make sure the filter cartridge is turned to the right as far as it will go. Also, check for crimps or
sharp bends in tubing. Check maintenance schedule for cartridge changeout.
Water appears cloudy or air comes out of filter faucet
Flushfilterfor1gallon(approximately2minutes)toremoveanycarbonfinesortrappedairinthefilterand
water lines. Longer flushing may be required to eliminate air bubbles completely.
CUNO Incorporated
400 Research Parkway
Meriden, CT 06450, USA
Toll Free: 1-888-218-CUNO
Worldwide: 203-237-5541
Fax: 203-238-8701
www.cuno.com
1
Push in grey collet to release tubing.
2
Tubing is secured in.
Grey Collet
Tube
Push tubing straight in as far as it will go.
1
Pull tubing straight out.
2
To Attach Tubing To Release Tubing
This product is outfitted with user friendly ‘Push In’ connectors. Proper use of the connectors is shown in
the diagrams.
It is most important that the tubing selected for use with these connectors be of high quality, exact size and
roundness, and with no surface nicks or scratches. If it is necessary to cut the tubing, use a plastic tubing
cutter or sharp razor knife. Make a clean square cut.
Shouldaleakoccurata‘Push-In’connector,thecauseisusuallydefectivetubing.
To Fix: •Relieve pressure • Release tubing • Cut off at least 1/4” from end
• Reattach tubing • Confirm connection is leak free
Figure 2.B
3M is a trademark of 3M Company.
John Guest is a trademark of John Guest International Limited.
© 2009 3M Company. All rights reserved.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels 3M Système de filtration d'eau
3M
3M Aqua-Pure APUN101 Manuel utilisateur
3M
3M SH-EXP Manuel utilisateur
3M
3M 28365 Manuel utilisateur
3M
3M 5000 Series Manuel utilisateur
3M
3M Triple Manifold Water Filtration Systems Manuel utilisateur
3M
3M 3MRO401 Manuel utilisateur
3M
3M AQUA-PURE IL-IM-01 Manuel utilisateur
3M
3M AP902 Series Manuel utilisateur
3M
3M ScaleGard HP Manuel utilisateur
3M
3M Aircare ACU-03 Manuel utilisateur
3M
3M Aqua-Pure AP717 Manuel utilisateur
3M
3M 5000 Series Manuel utilisateur
3M
3M 6051i Manuel utilisateur
3M
3M DF1 Series Manuel utilisateur
3M
3M AP902 Series Manuel utilisateur
3M
3M FR-64 Manuel utilisateur
3M
3M CUNO Aqua-Pure AP817 Manuel utilisateur
3M
3M Aqua-Pure AP810 Manuel utilisateur
3M
3M Aqua-Pure AP902 Manuel utilisateur
3M
3M W-2806/07006 Mode d’emploi
Manuels Système de filtration d'eau populaires d'autres marques
Wisy
Wisy LineAir 100 Manuel utilisateur
Schaffner
Schaffner Ecosine FN3446 Series Manuel d'utilisation
Pentair
Pentair FLECK 4600 SXT Guide de l'utilisateur
H2O International
H2O International H20-500 Manuel utilisateur
Renkforce
Renkforce 2306241 Manuel utilisateur
Neo-Pure
Neo-Pure TL3-A502 Manuel utilisateur
