IgniteNet MetroLinq ML2.5-60-35 Manuel utilisateur

– 1 –

Quick Start Guide

Unboxing

After opening the box, you will find…

◆MetroLinq™ (ML2.5-60-35, ML2.5-60-19, or ML2.5-60-BF-18)

◆PoE Power Supply

◆Power Cable

Tools/Items Required

◆13 mm Socket Wrench

◆Flat-Head Screwdriver

◆Ethernet Cables

Options

◆Standard Bracket ICC-BRACKET-STD

◆Long Range Precision Bracket ICC-BRACKET-LR

◆Alignment Scope ICC-SCOPE-9x50

For helpful training and user-case information, please go to

ignitenet.com/support

Assembly

The MetroLinq™ Standard Bracket and Long Range Precision Bracket

(both ordered separately) are designed for wall and pole mounting

(25 mm - 80 mm pole diameter). Choose what is best for your

location and select hardware accordingly.

Grounding

Welcome to MetroLinq™

Interference-Free Gigabit Wireless

Ensure all four position-locking bolts on the Standard

Bracket are tight before installing.

Install the Standard Bracket onto MetroLinq™ using four M8

bolts, lock washers, and flat washers.

Ensure the structure on which the unit is to be mounted is

properly grounded and in compliance with ETSI ETS 300

253.

Verify that there is a good electrical connection to a

grounding point (no paint or isolating surface treatment).

Use the included (M4) screw to attach a grounding wire (not

included) to the grounding point on the unit, and then to

ground.

Caution:

The earth connection must not be removed

unless all supply connections have been disconnected.

MetroLinq 2.5G

E102017-CS 15020000xxxxA R01

MetroLinq™2.5G Outdoor 60 GHz PTP/PTMP + 5 GHz

ML2.5-60-35 | ML2.5-60-19 | ML2.5-60-BF-18

www.ignitenet.com

Quick Start Guide

– 2 –

Power Up

Standard Bracket Alignment

IgniteNet strongly recommends using the ICC-SCOPE-9x50

Alignment Scope for alignment. To install, place the scope on top of

the MetroLinq™ housing and secure it with its thumb screw.

Connect an Ethernet cable from the MetroLinq™ ETH PoE IN

port to the PoE port on the power supply.

Connect Ethernet cable from the “LAN” port on the power

supply to your LAN device.

Connect the power cord to a nearby AC power source.

Note:

Do not adjust bolts A and B without first loosening 1

and 4 respectively.

Loosen coarse adjustment bolts 2 and 3 and set initial

alignment. Don’t worry, you don’t have to be too accurate

yet. After you have set the coarse alignment, tighten bolts 2

and 3.

Loosen the horizontal fine-tune adjustment bolt 4. Use fine-

tune bolt "B" to optimize the horizontal position. Re-tighten

bolt 4.

Loosen the vertical fine-tune adjustment bolt 1. Use fine-

tune bolt "A" to optimize the vertical position. Re-tighten

bolt 1.

Initial alignment should be based on optical or visual

alignment. After you achieve this, repeat steps 2 and 3 while

watching the 60 GHz signal strength LED. Optimize position

to the LED indicator.

Ensure all bolts are fully tightened, remove the alignment

scope (if installed), and enjoy Gigabit interference-free

wireless.

A23

Quick Start Guide

– 3 –

Software

For more configuration details and training, please go to

ignitenet.com/support

Safety and Regulatory Information

FCC Class B

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following

measures:

◆Reorient or relocate the receiving antenna

◆Increase the separation between the equipment and receiver

◆Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected

◆Consult the dealer or an experienced radio/TV technician for help

FCC Caution:Any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate this equipment.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

The 5600-5650MHz band is disabled by software during manufacturing

and cannot be changed by the end user. This device meets all the other

requirements specified in Part 15E,Section 15.407 of the FCC Rules.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 20 cm between the radiator and

your body.

Professional installation is required.

Note: The country code selection is for non-US models only and is not

available on all US models. Per FCC regulation, all Wi-Fi products

marketed in the US must be fixed to US operation channels only.

Professional Installation Instructions

1. Installation personal

This product is designed for specific applications and needs to be

installed by a qualified person who has RF and related rules knowledge.

The general user shall not attempt to install or change the settings.

2. Installation location

The product shall be installed at a location where the radiating antenna

can be kept 20 cm from nearby persons in normal operation conditions

to meet regulatory RF exposure requirements.

To configure your MetroLinq, connect your computer to the

device through the LAN port of the power supply or directly

to the ETH1 port on the device.

The default IP mode is DHCP client, so if the device obtains

an address from a DHCP server on the network, then use

that IP (you can use the Discovery Tool from the IgniteNet

support site to find the DHCP address). If the device does

not obtain a DHCP address, it reverts to the fallback IP of

192.168.1.20 and you can access it on that IP. Direct your

web browser to the correct IP and log in.

username: root

password: admin123

After you have logged in, follow the steps in the Setup

Wizard to configure the device for your network.

After you have logged in, follow the steps in the Setup

Wizard to configure the device for your network.

Quick Start Guide

– 4 –

3. External antenna

Use only the antennas that have been approved by the applicant. Non-

approved antenna(s) may produce unwanted spurious or excessive RF

transmitting power, which may lead to the violation of FCC/IC limits and

is prohibited.

4. Installation procedure

Please refer to user's manual for details.

5. Warning

Please carefully select the installation position and make sure that the

final output power does not exceed the limits set forcth in relevant rules.

Violation of the rules could lead to serious federal penalties.

Instructions d'installation professionnelle

1. Installation

Ce produit est destiné àun usage spécifique et doit être installé par un

personnel qualifié maîtrisant les radio-fréquences etles règles s'y

rapportant. L'installation et les réglages ne doivent pas être modifiés par

l'utilisateur final.

2. Emplacement d'installation

En usage normal, afin de respecter les exigences réglementaires

concernant l'exposition aux radio-fréquences, ce produit doit être

installé de façon à respecter une distance de 20 cm entre l'antenne

émettrice et les personnes.

3. Antenne externe

Utiliser uniquement les antennes approuvées par le fabricant.

L'utilisation d'autres antennes peut conduire à un niveau de

rayonnement essentiel ou non essentiel dépassant les niveaux limites

définis par FCC/IC, ce qui est interdit.

4. Procedure d'installation

Consulter le manuel d'utilisation.

5. Avertissement

Choisir avec soin la position d'installation et s'assurer que la puissance

de sortie ne depasse pas les limites en vigueur. La violation de cette

règle peut conduire à de sérieuses pénalites fédérales.

IC Statement

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

This radio transmitter (IC: 3857A-ML2560) has been approved by

Industry Canada to operate with the antenna types listed below with the

maximum permissible gain indicated. Antenna types not included in this

list, having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Le présent émetteur radio (IC: 3857A-ML2560) a été approuvé par Industrie

Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et

ayant un gain admissible maximal d'antenne. Les types d'antenne non

inclus dans cette liste, ou dont le gain est supérieur au gain maximal

indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

5G Antenna List:

60G Antenna List:

The maximum antenna gain permitted for devices in the band 5725-

5850 MHz shall be such that the equipment still complies with the e.i.r.p.

limits specified for point-to-point and non-point-to-point operation as

appropriate.

Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande

5725-5850 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour

l’exploitation point à point et non point à point, selon le cas.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 23 cm between the

radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC

établies pour un environnement non contrôlé. Cet équipement doit être

installé et utilisé avec un minimum de 23 cm de distance entre la source de

rayonnement et votre corps.

CE Mark

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This is a class B product. In a domestic environment, this product may

cause radio interference, in which case the user may be required to take

adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and

other countries following the EU directive 1999/5/EC) without any

limitation except for the countries mentioned below:

Ant. Brand P/N Antenna Type Connector Gain (dBi)

Band 1 Band 4

Dish N/A 10.112.11 Accton 120G00000176X

Ant. Brand P/N Antenna Type Connector Gain (dBi)

Dish N/A 17.2

1 Accton 120300000225X

Country Restriction Reason/Remark

Bulgaria None General authorization required for

outdoor use and public service

France Outdoor use limited

to 10 mW e.i.r.p.

within the band

2454-2483.5 MHz

Military Radiolocation use.

Refarming of the 2.4 GHz band has

been ongoing in recent years to

allow current relaxed regulation.

Full implementation planned 2012

italy None If used outside of own premises,

general authorization is required

Luxembourg None General authorization required for

network and service supply(not for

spectrum)

It should be 2014/53/EC

There is no application band 2454-2483.5 MHz, so please remove.

Quick Start Guide

– 5 –

Europe - EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE

Directive 1999/5/EC. The following test methods have been applied in

order to prove presumption of conformity with the essential

requirements of the R&TTE Directive 1999/5/EC:

◆EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

Safety of Information Technology Equipment.

◆EN 300 328 V1.8.1: 2012

Electromagnetic compatibility and Radio spectrum Matters (ERM);

Wideband transmission systems; Data transmission equipment

operating in the 2,4 GHz ISM band and using wide band modulation

techniques; Harmonized EN covering essential requirements under

article 3.2 of the R&TTE Directive.

◆EN 301 489-1 V1.9.2 (2011-09)

EN 301 489-7 V1.3.1/ 2005

Electromagnetic compatibility and Radio spectrum Matters (ERM);

Electromagnetic Compatibility (EMC) standard for radio equipment

and services; Part 17: Specific conditions for 2.4 GHz wideband

transmission systems and 5 GHz high performance RLAN

equipment.

◆EN 55022 2010 + AC: 2011

Limits and methods of measurement of radio disturbance

characteristics of information technology equipment.

◆EN 55024: 2010

Information technology equipment immunity characteristics limits

and methods of measurement.

◆EN 62311: 2008

Assessment of electronic and electrical equipment related to

human exposure restrictions for electromagnetic fields (0 Hz - 300

GHz).

This device is a 2.4 GHz wideband transmission system (transceiver),

intended for use in all EU member states and EFTA countries, except in

France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum

authorities in order to obtain authorization to use the device for setting

up outdoor radio links and/or for supplying public access to

telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France

and in some areas the RF output power may be limited to 10 mW EIRP in

the frequency range of 2454 - 2483.5 MHz. For detailed information the

end-user should contact the national spectrum authority in France.

The Declaration of Conformity (DoC) can be obtained from

www.ignitenet.com -> support -> download -> declarations &

certifications.

This equipment may be operated in:

Norway Implemented This subsection does not apply for

the geographical area within a

radius of 20 km from the centre of

Ny-Ålesund

Russian

Federation None Only for indoor applications

Note:

Do not use the product outdoors in France.

Country Restriction Reason/Remark

Bulgarian

Български

Снастоящето, IgniteNet декларира, че това безжично

устройство евсъответствие със съществените

изисквания идругите приложими разпоредби на

Директива 1999/5/EC.

Czech

Česky

IgniteNet tímto prohlašuje, že tento Radio LAN device je ve

shoděse základními požadavky a dalšími příslušnými

ustanoveními směrnice 1999/5/ES.

Danish

Dansk

Undertegnede IgniteNet erklærer herved, at følgende udstyr

Radio LAN device overholder de væsentlige krav og øvrige

relevante krav i direktiv 1999/5/EF

Dutch

Nederlands

Hierbij verklaart IgniteNet dat het toestel Radio LAN device in

overeenstemming is met de essentiële eisen en de andere

relevante bepalingen van richtlijn 1999/5/EG

Bij deze IgniteNet dat deze Radio LAN device voldoet aan de

essentiële eisen en aan de overige relevante bepalingen van

Richtlijn 1999/5/EC.

English Hereby, IgniteNet, declares that this Radio LAN device is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Estonian

Eesti

Käesolevaga kinnitab IgniteNet seadme Radio LAN device

vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud

direktiivist tulenevatele teistele asjakohastele sätetele.

Finnish

Suomi

Valmistaja IgniteNet vakuuttaa täten että Radio LAN device

tyyppinen laite on direktiivin 1999/5/EY oleellisten

vaatimusten ja sitä koskevien direktiivin muiden ehtojen

mukainen.

French

Français

Par la présente IgniteNet déclare que l'appareil Radio LAN

device est conforme aux exigences essentielles et aux

autres dispositions pertinentes de la directive 1999/5/CE.

German

Deutsch

Hiermit erklärt IgniteNet, dass sich dieser/diese/dieses Radio

LAN device in Übereinstimmung mit den grundlegenden

Anforderungen und den anderen relevanten Vorschriften der

Richtlinie 1999/5/EG befindet. (BMWi)

Hiermit erklärt IgniteNet die Übereinstimmung des Gerätes

Radio LAN device mit den grundlegenden Anforderungen

und den anderen relevanten Festlegungen der Richtlinie

1999/5/EG. (Wien)

Greek

Ελληνική

με την παρουσα IgniteNet δηλωνει οτι radio LAN device

συμμορφωνεται προσ τισ ουσιωδεισ απαιτησεισ και τισ

λοιπεσ σχετικεσ διαταξεισ τησ οδηγιασ 1999/5/εκ.

Hungarian

Magyar

Alulírott, IgniteNet nyilatkozom, hogy a Radio LAN device

megfelel a vonatkozó alapvetõ követelményeknek és az

1999/5/EC irányelv egyéb elõírásainak.

Italian

Italiano

Con la presente IgniteNet dichiara che questo Radio LAN

device è conforme ai requisiti essenziali ed alle altre

disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

It should be RED

It should be 2014/53/EU

It should be RED Directive 2014/53/EU

It should be EN 301 893 V2.1.1 and EN 302 567 V2.1.1(2017-07)

There is no application band 2454-2483.5 MHz, so please moify to 5 GHz

It should be RED

It should be V2.1.1(2017-02)

It should be Final draft EN 301 489-3 V2.1.1 (2017-03)

There is no application band 2.4 MHz, so please remove,It application 5 GHz & 60 GHz.

Please add EN 301 489-17 V3.1.1 (2017-02)

It should be EN 55032:2015

There is no application this standard

It should be EN 62311:2008 and EN 50385:2002

There is no application band 2.4 MHz, so please remove,it application 5 GHz & 60 GHz.

There is no application band 2454-2483.5 MHz, so please remove.

as blow remark: For English, it should be 2014/53/EU

It should be Pictogram logo.

It should be The device fixed outdoor installations is not allowed.

Quick Start Guide

– 6 –

NCC Statement (Taiwan)

低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或

使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經

發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前

項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍

受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

電磁波曝露量 MPE 標準值 1mW/cm²，本產品使用時建議應距離人體

58 cm。

TELEC Statement (Japan)

5.2/5.3GHz帯の無線LAN 製品は法令により屋外では使用できません。

屋內のみでご使用ください。

All wireless LAN products in the 5.2/5.3GHz band cannot be used

outdoors. Use the product only indoors.

Warnings and Cautionary Messages

Latvian

Latviski

Ar šo IgniteNet deklarē, ka Radio LAN device atbilst

Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to

saistītajiem noteikumiem.

Lithuanian

Lietuvių

Šiuo IgniteNet deklaruoja, kad šis Radio LAN device atitinka

esminius reikalavimus ir kitas 1999/5/EB Direktyvos

nuostatas.

Maltese

Malti

Hawnhekk, IgniteNet, jiddikjara li dan Radio LAN device

jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti

oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Polish

Polski

Niniejszym IgniteNet oświadcza, że Radio LAN device jest

zgodny z zasadniczymi wymogami oraz pozostałymi

stosownymi postanowieniami Dyrektywy 1999/5/EC.

Portuguese

Português

IgniteNet declara que este Radio LAN device está conforme

com os requisitos essenciais e outras disposições da

Directiva 1999/5/CE.

Romanian

Romană

IgniteNet declarăcăacest dispozitiv fărăfir respectă

cerinţele esenţiale precum şi alte dispoziţii relevante ale

Directivei 1999/5/EC.

Slovak

Slovensky

IgniteNet týmto vyhlasuje, že Radio LAN device spĺňa

základné požiadavky a všetky príslušné ustanovenia

Smernice 1999/5/ES.

Slovenian

Slovensko

IgniteNet izjavlja, da je ta radio LAN device v skladu z

bistvenimi zahtevami in ostalimi relevantnimi določili direktive

1999/5/ES.

Spanish

Español

Por medio de la presente IgniteNet declara que el Radio LAN

device cumple con los requisitos esenciales y cualesquiera

otras disposiciones aplicables o exigibles de la Directiva

1999/5/CE

Swedish

Svenska

Härmed intygar IgniteNet att denna Radio LAN device står I

överensstämmelse med de väsentliga egenskapskrav och

övriga relevanta bestämmelser som framgår av direktiv

1999/5/EG.

Turkish

Turk

IgniteNet bu kablosuz cihazın temel gereksinimleri ve 1999/

5/EC yonergesindeki ilgili koşullarıkarşıladığınıbeyan eder.

Warning:

This product does not contain any serviceable user

parts.

Warning:

Installation and removal of the unit must be carried

out by qualified personnel only.

Warning:

When connecting this device to a power outlet,

connect the field ground lead on the tri-pole power plug to a

valid earth ground line to prevent electrical hazards.

Caution:

Wear an anti-static wrist strap or take other suitable

measures to prevent electrostatic discharge when handling this

equipment.

Caution:

Do not plug a phone jack connector in the RJ-45

port. This may damage this device.

Caution:

Use only twisted-pair cables with RJ-45 connectors

that conform to FCC standards.

Telec Statement (Japan): There is no application band 5.2G/5.3G and this product is outdoor use, so please removied it.

Quick Start Guide

– 7 –

Hardware Specifications

Chassis

Size (L x W x H:)

Weight

Temperature

Humidity

ML2.5-60-35:

350 x 350 x 200 mm (13.78 x 13.78 x 7.87 in.)

ML2.5-60-19:

190 x 190 x120 mm (7.48 x 7.48 x 4.72 in.)

ML2.5-60-BF-18:

190 x 190 x 60 mm (7.48 x 7.48 x 2.36 in.)

ML2.5-60-35: 3.5 kg (7.72 lb)

ML2.5-60-19: 2 kg (4.41 lb)

ML2.5-60-BF-18: 2 kg (4.41 lb) with mount

Operating: -30 °C to55 °C (-22 °F to 131 °F) / ML2.5-60-BF-18: -40 °C to 70 °C (-40 °F to 158 °F)

Storage: -40 °C to 70 °C (-40 °F to 158 °F)

Operating: 10% to 90% (non-condensing)

Network Interfaces

Ports ETH RJ-45 Port: 1000BASE-T, passive PoE

SFP Port: 1000BASE-X

60 GHz Radio IEEE 802.11ad

5 GHz Radio IEEE 802.11ac

Radio Frequencies 5150 ~ 5250 MHz (FCC)

5725 ~ 5850 MHz (FCC)

5745 ~ 5825 MHz (China)

5180 ~ 5320 MHz (ETSI)

5500 ~ 5700 MHz (ETSI)

58.32 ~ 64.80 GHz

Power Supply

Passive PoE 48 VDC, maximum 0.5 A

Power Consumption 24 W maximum

Regulatory Compliances

Radio EN 300 328 V1.8.1:2012

EN 301 893 V1.7.1:2012

EN 301 489-1 V1.9.2 (2011-09)

EN 301 489-17 V2.2.1:2012

FCC Part 15C 15.247/15.207 (2.4-2.4835GHz)

FCC Part 15E 15.407 (5.150GHz-5.250GHz,

5.725-5.850GHz)

Emissions EN 55022 2010+AC:2011

EN 61000-3-2 2006+A1:2009+A2:2009

FCC Class B Part 15

Immunity EN 55024 : 2010

EN 61000-4-2 : 2009

Please modify to as below :

ICES-003 Class B

IC RSS-247 Issue 2 and RSS-Gen Issue 4

RSS-102 Issue 5

47 CFR Part 2.1091

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IgniteNet Matériel réseau

IgniteNet

IgniteNet GLinq GL-O-1GE-1C Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur