AWID SENTINEL-SENSE ADB-510 Manuel utilisateur

ADB-510 Page 1 7/16/2021

APPLIED WIRELESS ID

SENTINEL-SENSE ADB-510

INSTALLATION & OPERATION MANUAL - 041526

ADB-510 Page 2 7/16/2021

APPLIED WIRELESS ID

The contents of this document are the property of Applied Wireless Identifications Group, Inc.

strictly prohibited. For additionalcopies of this document please contact:

AWID

18300 Sutter Blvd

Morgan Hill, CA 95037

http://www.AWID.com

The information contained herein has been carefully checked and is believed to be accurate,

no responsibility is assumed for inaccuracies. AWID reservesthe right to make changes

without prior notice. This document is not covered by any warrantyeither expressed or

implied. Any comments, corrections or additions to the contents of this documentshould be

directed to AWID at the above address.

All other trademarks are the property of their respective owners.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

ADB-510 Page 3 7/16/2021

APPLIED WIRELESS ID

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 23

cm between the radiator & your body.

This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM

Manual v01 guidance, the following conditions must be strictly followed when using

this certified module:

KDB 996369 D03 OEM Manual v01 rule sections:

2.2 List of applicable FCC rules

This module has been tested for compliance to FCC Part 15

2.3 Summarize the specific operational use conditions

The module is tested for standalone mobile RF exposure use condition. Any other

usage conditions such as co-location with other transmitter(s) or being used in a

portable condition will need a separate reassessment through a class II permissive

change application or new certification.

2.4 Limited module procedures

Not applicable.

2.5 Trace antenna designs

Not applicable.

2.6 RF exposure considerations

This equipment complies with FCC mobile radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a

minimum distance of 23 cm between the radiator & your body. If the module is

installed in a portable host, a separate SAR evaluation is required to confirm

compliance with relevant FCC portable RF exposure rules.

2.7 Antennas

The following antennas have been certified for use with this module; antennas of the same type

with equal or lower gain may also be used with this module. The antenna must be installed such

that 23 cm can be maintained between the antenna and users.

Manufacturer/

Brand

Model

Antenna

Type

Antenna

connector

Max Gain (dBi)

Impedance (Ω)

AWID

ANT-915CPS

Patch

TNC, RP

5.8

AWID

ANT-915-CP-R

Patch

SMA, RP

5.5

AWID

ANT-2012

Patch

SMA, RP

5.4

AWID

ANT-915-CC-05

Patch

TNC, RP

4.7

ADB-510 Page 4 7/16/2021

APPLIED WIRELESS ID

2.8 Label and compliance information

The final end product must be labeled in a visible area with the following: “Contains

FCC ID: OGSADB510”. The grantee's FCC ID can be used only when all FCC

compliance requirements are met.

2.9 Information on test modes and additional testing requirements

This transmitter is tested in a standalone mobile RF exposure condition and any

co-located or simultaneous transmission with other transmitter(s) or portable use

will require a separate class II permissive change re-evaluation or new certification.

2.10 Additional testing, Part 15 Subpart B disclaimer

This transmitter module is tested as a subsystem and its certification does not

cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement

applicable to the final host. The final host will still need to be reassessed for

compliance to this portion of rule requirements if applicable.

As long as all conditions above are met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example

certain laptop configurations or co-location with another transmitter), then the FCC

authorization is no longer considered valid and the FCC ID cannot be used on the final

product. In these circumstances, the OEM integrator will be responsible for re-evaluating

the end product (including the transmitter) and obtaining a separate FCC authorization.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.

The end user manual shall include all required regulatory information/warning as show in

this manual.

OEM/Host manufacturer responsibilities

OEM/Host manufacturers are ultimately responsible for the compliance of the Host and

Module. The final product must be reassessed against all the essential requirements of

the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market.

This includes reassessing the transmitter module for compliance with the Radio and EMF

essential requirements of the FCC rules. This module must not be incorporated into any

other device or system without retesting for compliance as multi-radio and combined

equipment.

ADB-510 Page 5 7/16/2021

APPLIED WIRELESS ID

INDUSTRY CANADA COMPLIANCE

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le

dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter

tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement

indésirable.

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 34

cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies

pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un

minimum de 34 cm de distance entre la source de rayonnement et votre corps.

This device is intended only for OEM integrators under the following conditions:

(For module device use)

1) The antenna must be installed such that 34 cm is maintained between the antenna

and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required.

However, the OEM integrator is still responsible for testing their end-product for any

additional compliance requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions

suivantes: (Pour utilisation de dispositif module)

1) L'antenne doit être installée de telle sorte qu'une distance de 34 cm est respectée

entre l'antenne et les utilisateurs, et

2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur

l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours

responsable des essais sur son produit final pour toutes exigences de conformité

supplémentaires requis pour ce module installé.

ADB-510 Page 6 7/16/2021

APPLIED WIRELESS ID

DETACHABLE ANTENNA USAGE

This radio transmitter [IC: 6449A-ADB510] has been approved by Innovation, Science

and Economic Development Canada to operate with the antenna types listed below,

with the maximum permissible gain indicated. Antenna types not included in this list

that have a gain greater than the maximum gain indicated for any type listed are

strictly prohibited for use with this device.

Le présent émetteur radio [IC: 6449A-ADB510] a été approuvé par Innovation, Sciences

et Développement économique Canada pour fonctionner avec les types d'antenne

énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non

inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout

type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.

Manufacturer/

Brand

Model

Antenna

Type

Antenna

connector

Max Gain (dBi)

Impedance (Ω)

AWID

ANT-915CPS

Patch

TNC, RP

5.8

AWID

ANT-915-CP-R

Patch

SMA, RP

5.5

AWID

ANT-2012

Patch

SMA, RP

5.4

AWID

ANT-915-CC-05

Patch

TNC, RP

4.7

IMPORTANT NOTE:

In the event that these conditions cannot be met (for example certain laptop

configurations or co-location with another transmitter), then the Canada authorization is

no longer considered valid and the IC ID cannot be used on the final product. In these

circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines

configurations d'ordinateur portable ou de certaines co-localisation avec un autre

émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut

pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera

chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation

distincte au Canada.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be

installed such that 34 cm may be maintained between the antenna and users. The final

end product must be labeled in a visible area with the following: “Contains IC:6449A-

ADB510”.

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où

l'antenne peut être installée de telle sorte qu'une distance de 34 cm peut être maintenue

ADB-510 Page 7 7/16/2021

APPLIED WIRELESS ID

entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible

avec l'inscription suivante: "Contient des IC: 6449A-ADB510".

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.

The end user manual shall include all required regulatory information/warning as show in

this manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur

final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de

l'utilisateur du produit final qui intègre ce module.

Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires

requises et avertissements comme indiqué dans ce manuel.

ADB-510 Page 8 7/16/2021

APPLIED WIRELESS ID

Table of Content

FCC COMPLIANCE......................................................................................................................2

INDUSTRY CANADA COMPLIANCE.......................................................................................5

REVISION HISTORY..................................................................................................................9

1. INTRODUCTION.................................................................................................................10

1.1. SPECIAL FEATURES..........................................................................................................10

2. SPECIFICATIONS...............................................................................................................11

2.1. CHANNEL FREQUENCY TABLE .........................................................................................11

2.2. CONNECTOR PIN ASSIGNMENT ........................................................................................12

2.3. MEASURING READ DISTANCE..........................................................................................12

3. INSTALLATION & OPERATION GUIDELINES..........................................................13

3.1. GENERAL WIRING REQUIREMENTS ...................................................................................13

4. INSTALLATION PROCEDURE........................................................................................14

4.1. PARTS LIST ......................................................................................................................14

4.2. PREPARATION FOR INSTALLATION ...................................................................................14

4.2.1. Bench Top Verification ...........................................................................................14

NOTES ON SOFTWARE PROGRAMMING AND SYSTEM OPERATION ......................15

4.3. SYSTEM OPERATION ........................................................................................................15

4.3.1. Running a Custom Software Application or the AWID Demo Program ................15

4.4. USERS NOTE ....................................................................................................................15

5. REFERENCE........................................................................................................................16

NOTE: READ AND USE THIS MANUAL

FAILURE TO FOLLOW THE INSTALLATION (SET UP) GUIDE MAY RESULT IN

POOR PERFORMANCE OR EVEN CAUSE PERMANENT DAMAGE TO THE

READER, THUS VOIDS THE PRODUCT WARRANTY.

ADB-510 Page 9 7/16/2021

APPLIED WIRELESS ID

REVISION HISTORY

Version

No.

Revised By

Date

Sections

Affected

Remarks

0.1

AWID Engineering

6/2021

Initial version

0.2

AWID Engineering

7/2021

p.5

Editorial - IC Compliance statement

0.3

AWID Engineering

7/2021

p.2, p.5

Updated – FCC, IC Compliance

ADB-510 Page 10 7/16/2021

APPLIED WIRELESS ID

1. INTRODUCTION

AWID's Sentinel-Sense ADB-510 is a single-port, long-range Radio Frequency

IDentification (RFID) reader module with 3.3 V TTL logical interface that works with most

leading UHF passive tags. The reader module comes with a unique combination of long

read range, small size, and low power consumption. Its primary applications are asset

management and tracking, and fleet management applications.

ADB-510 is delivered with Firmware Version such as US0-62.xx.xx.

In order to operate an ADB-510 you will need the following:

PC running Windows 7

or higher and one serial port

Host software (AWID’s demo software or your own custom software)

1.1. SPECIAL FEATURES

Multi-Protocol: ISO-18000-6 Type C, EPC Class 1 Gen 2

Thin passive tags with long-range performance

3.3 V (5.0V tolerable) Serial TTL logical interface

Though ADB-510 can also be controlled from a non-Windows programming platform, AWID demo and

FW upgrade programs are applications to run in Windows.

Table des matières

Autres manuels AWID Unité de contrôle

AWID

AWID SENTINEL-SENSE MPR-1510 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur